Manuals+

Xigmatek EN42098

Xigmatek Galaxy II Elite AY120 ARGB Fan Pack Instruction Manual

Model: EN42098

1. Introduction

This instruction manual provides comprehensive guidance for the installation, operation, and maintenance of your Xigmatek Galaxy II Elite AY120 ARGB 3-fan pack. This product is designed to enhance your computer system's cooling performance and aesthetic appeal with addressable RGB lighting. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.

2. Safety Information

  • Always disconnect power from your computer before installing or removing any components.
  • Handle components with care to avoid damage from electrostatic discharge. Consider using an anti-static wrist strap.
  • Ensure all cables are connected securely and correctly to prevent short circuits or malfunction.
  • Do not attempt to modify the product. Unauthorized modifications may void your warranty and pose safety risks.
  • Keep the product away from liquids and extreme temperatures.

3. Package Contents

Verify that all items listed below are present in your package:

  • 3 x Xigmatek Galaxy II Elite AY120 ARGB Fans (120mm)
  • 1 x ARGB Control Box
  • 1 x IR Remote Control
  • Mounting Screws
Xigmatek Galaxy II Elite AY120 ARGB 3-fan pack with controller and remote

Image 3.1: Contents of the Xigmatek Galaxy II Elite AY120 ARGB 3-fan pack, including three 120mm ARGB fans, the ARGB control box, and the IR remote control.

4. Setup and Installation

Follow these steps to install your Xigmatek Galaxy II Elite AY120 ARGB fans:

  1. Prepare Your System: Power off your computer and disconnect it from the power outlet. Open your computer case.
  2. Mount the Fans:
    • Identify the desired mounting locations for the 120mm fans within your PC case (e.g., front, top, rear).
    • Secure each fan to the case using the provided mounting screws. Ensure the fan's airflow direction is appropriate for your cooling setup (typically intake at the front/bottom, exhaust at the rear/top).
  3. Connect Fans to Control Box:
    • Connect the 6-pin fan cables from each of the three AY120 ARGB fans to the corresponding ports on the ARGB Control Box.
    • Ensure connections are firm.
  4. Connect Control Box to Power:
    • Connect the SATA power connector from your power supply unit (PSU) to the ARGB Control Box. This provides power to the fans and RGB lighting.
  5. Connect Control Box to Motherboard (Optional ARGB Sync):
    • If your motherboard has a 5V 3-pin Addressable RGB (ARGB) header, you can connect the ARGB sync cable from the control box to this header. This allows you to control the fan lighting via your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync).
    • Note: Do not connect to a 12V 4-pin RGB header, as this will damage the fans.
  6. Cable Management: Route all cables neatly to ensure proper airflow and a clean build.
  7. Final Steps: Close your computer case, reconnect the power, and power on your system.
Top view of a single Xigmatek Galaxy II Elite AY120 ARGB fan displaying its vibrant RGB lighting

Image 4.1: A single Xigmatek Galaxy II Elite AY120 ARGB fan, showcasing its illuminated blades and frame.

5. Operating Instructions

Once installed, you can control the ARGB lighting of your fans using either the included IR remote control or your motherboard's software (if connected to a 5V ARGB header).

5.1. Using the IR Remote Control

The IR remote allows you to cycle through various lighting effects, adjust brightness, and change colors. Point the remote directly at the ARGB Control Box for optimal response.

  • Power Button: Turn ARGB lighting On/Off.
  • Mode Buttons: Cycle through different lighting modes and effects.
  • Speed Buttons: Adjust the speed of dynamic lighting effects.
  • Brightness Buttons: Increase or decrease the brightness of the lighting.
  • Color Buttons: Select static colors or color cycling modes.

5.2. Motherboard ARGB Software Control

If you have connected the control box to your motherboard's 5V 3-pin ARGB header, you can use your motherboard's proprietary software to synchronize and customize the lighting effects. Refer to your motherboard's manual for specific instructions on using its ARGB software.

  • Ensure the ARGB sync cable is properly connected.
  • Install the latest version of your motherboard's RGB control software.
  • Select the appropriate ARGB device within the software to control the fans.

6. Maintenance

Regular maintenance helps ensure optimal performance and longevity of your fans.

  • Cleaning: Periodically clean the fan blades and frames to remove dust buildup. Use a soft brush or compressed air. Ensure the computer is powered off and unplugged before cleaning.
  • Inspection: Check fan cables for any signs of wear or damage. Ensure all connections remain secure.
  • Do Not Lubricate: The fan bearings are sealed and do not require lubrication. Attempting to lubricate them may cause damage.

7. Troubleshooting

If you encounter issues with your Xigmatek Galaxy II Elite AY120 ARGB fans, refer to the following common problems and solutions:

Problem Possible Cause Solution
Fans are not spinning.
  • No power to control box.
  • Loose fan cable connection.
  • Faulty control box or fan.
  • Ensure SATA power cable is securely connected to the control box and PSU.
  • Check all 6-pin fan cables are firmly seated in the control box.
  • Test individual fans if possible. Contact support if components are faulty.
ARGB lighting is not working.
  • No power to control box.
  • Loose ARGB cable connection.
  • IR remote battery dead or signal blocked.
  • Incorrect motherboard ARGB header connection (e.g., 12V instead of 5V).
  • Motherboard software not configured.
  • Verify SATA power connection to the control box.
  • Check 6-pin fan cables and ARGB sync cable connections.
  • Replace IR remote battery or ensure clear line of sight to control box.
  • Confirm connection to a 5V 3-pin ARGB header only.
  • Ensure motherboard ARGB software is running and configured correctly.
Fans are making unusual noise.
  • Obstruction (cable, dust).
  • Loose mounting screws.
  • Faulty fan bearing.
  • Inspect for any cables or debris touching the fan blades.
  • Tighten mounting screws.
  • If noise persists, the fan may be faulty and require replacement.

8. Specifications

Feature Detail
Model Number EN42098
Fan Size 120mm
Lighting Type Addressable RGB (ARGB)
Voltage 5 Volts
Power Connector 6-pin (fan), SATA (control box)
Motherboard Sync 5V 3-pin ARGB Header (compatible with ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync)
Control Method IR Remote Control, Motherboard Software (via ARGB sync)
Noise Level 1 Sones
Package Dimensions 20.1 x 13.5 x 10.1 cm
Package Weight 630 grams

9. Warranty and Support

Xigmatek products are manufactured to high-quality standards. For warranty information, technical support, or replacement parts, please refer to the official Xigmatek website or contact your local retailer. Keep your proof of purchase for warranty claims.

For further assistance, please visit: www.xigmatek.com