1. Introduction
This manual provides essential information for the safe and efficient installation, operation, and maintenance of the MEAN WELL LPV-100-12 LED Driver. This unit is a constant voltage, single output, waterproof power supply designed for LED-related fixtures and appliances. It features a universal AC input and is fully encapsulated with an IP67 rating, making it suitable for various environments.
2. Safety Instructions
Read all instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or other hazards.
- Qualified Personnel: Installation and servicing must be performed by qualified personnel only.
- Power Disconnection: Always disconnect power before installation, maintenance, or troubleshooting.
- Proper Wiring: Ensure all wiring connections are secure and comply with local electrical codes. Incorrect wiring can cause damage or fire.
- Ventilation: Although IP67 rated, ensure adequate air circulation around the unit to prevent excessive heat buildup, especially when operating at maximum load.
- Load Compatibility: Do not exceed the specified output wattage or current. Overloading can damage the driver and connected devices.
- Environmental Conditions: The IP67 rating indicates suitability for dry and damp locations. Avoid submerging the unit or exposing it to extreme temperatures outside its specified operating range.
3. Product Overview
The LPV-100-12 is a robust LED driver designed for reliable performance in demanding conditions. Its compact form factor and waterproof design make it versatile for various applications.
Figure 3.1: Overall view of the MEAN WELL LPV-100-12 LED Driver. This image displays the white rectangular housing with input (AC) and output (DC) wires, along with the product label.
Figure 3.2: Close-up of the product label on the LPV-100-12. The label details input voltage (100-240V~, 2.2A, 50/60Hz), output voltage (+12V === 8.5A), and various certifications including CE, cURus, and IP67.
Figure 3.3: Product label with the serial number highlighted. The serial number for this unit is GB95522023. This serial number can be used to obtain the Quality Control Inspection Report from MEAN WELL.
4. Setup and Installation
Follow these steps for proper installation of the LPV-100-12 LED Driver.
- Mounting: The unit is designed for wall mount installation. Secure the driver to a stable surface using appropriate fasteners. Ensure the mounting location allows for adequate heat dissipation.
- Input Wiring (AC):
- Connect the Brown (ACL) wire to the Live (L) AC input.
- Connect the Blue (ACN) wire to the Neutral (N) AC input.
- The input voltage range is 90 ~ 264VAC or 127 ~ 370VDC. Ensure your power source is within this range.
- Output Wiring (DC):
- Connect the Red (V+) wire to the positive (+) terminal of your 12VDC LED fixture.
- Connect the Black (V-) wire to the negative (-) terminal of your 12VDC LED fixture.
- Ensure the total power consumption of the connected LED fixtures does not exceed 102 Watts (8.5 Amps at 12VDC).
- Insulation: After making all connections, ensure all exposed wires are properly insulated to prevent short circuits.
- Power On: Once all connections are secure and verified, apply power to the AC input.
5. Operating Instructions
The MEAN WELL LPV-100-12 is a constant voltage LED driver. Once properly installed and powered, it will provide a stable 12VDC output to the connected LED load.
- Automatic Operation: The driver operates automatically when power is supplied. There are no user-adjustable controls.
- Load Monitoring: Ensure the connected LED load remains within the driver's specified output limits (12VDC, 8.5A, 102W).
- Protection Features: The unit includes built-in protections against short circuit, overload, and over voltage. In case of a fault, the driver may temporarily shut down to protect itself and the connected load. Remove the fault condition and cycle power to reset.
6. Maintenance
The LPV-100-12 LED Driver is designed for minimal maintenance due to its fully encapsulated, waterproof construction.
- Regular Inspection: Periodically inspect the driver and its wiring for any signs of damage, wear, or loose connections.
- Cleaning: If necessary, gently clean the exterior of the unit with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure the unit is powered off before cleaning.
- Environmental Check: Verify that the operating environment remains within the specified temperature range (-25~70℃) and that the IP67 rating is not compromised by physical damage.
7. Troubleshooting
If you encounter issues with your LPV-100-12 LED Driver, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| No output from driver / LEDs not lighting up |
|
|
| LEDs flickering or dim |
|
|
| Driver is hot to the touch |
|
|
8. Specifications
Detailed technical specifications for the MEAN WELL LPV-100-12 LED Driver:
| Feature | Specification |
|---|---|
| Model Number | LPV-100-12 |
| Input Voltage | 90 ~ 264VAC or 127 ~ 370VDC |
| Input Frequency | 47 ~ 63Hz |
| Input Current | 2.2A/115VAC, 1.2A/230VAC |
| Output Voltage | 12VDC |
| Output Current | 8.5 Amps |
| Output Wattage | 102 Watts |
| Efficiency | Not specified in provided data, typical for constant voltage drivers. |
| Protections | Short Circuit, Overload, Over Voltage |
| Operating Temperature | -25 ~ 70℃ |
| Ingress Protection (IP) Rating | IP67 (Fully encapsulated, suitable for dry and damp locations) |
| Dimensions (L x W x H) | 7.48 x 2.05 x 1.46 inches (190 x 52 x 37 mm) |
| Item Weight | 0.16 ounces (approx. 4.54 g) |
| Mounting Type | Wall Mount |
| UPC | 645312123049 |
9. Warranty and Support
For warranty information and technical support, please refer to the official MEAN WELL website or contact your authorized distributor. Keep your purchase receipt and the product's serial number (e.g., GB95522023) for any warranty claims or support inquiries.
