1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of the CAME 806SL-0170 Wireless Code Lock. This surface-mounted keypad offers secure and convenient access control for various applications, featuring a 433.92 MHz wireless frequency, a grey cover, and a blue backlight for enhanced visibility.
2. Product Overview and Components
The CAME 806SL-0170 Wireless Code Lock is designed for robust outdoor use, providing reliable access control through a programmable keypad.
Figure 2.1: Front view of the CAME 806SL-0170 Wireless Code Lock, showing the 12-key keypad and the CAME branding.
Package Contents:
- CAME SEL SELT1W4G Wireless Code Lock unit (Grey Cover)
- Mounting screws
- Gasket for weather sealing
- Battery (CR123A)
Figure 2.2: Exploded view showing the main keypad unit, rear housing, sealing gasket, CR123A battery, and mounting screws.
3. Setup and Installation
The CAME 806SL-0170 is designed for surface mounting and operates wirelessly, simplifying installation.
3.1 Battery Installation
- Carefully open the rear casing of the keypad unit.
- Insert one CR123A battery into the designated battery compartment, ensuring correct polarity (+/-).
- Close the rear casing securely.
3.2 Mounting the Keypad
- Choose a suitable flat surface for mounting, ensuring it is within range of your CAME radio receiver (e.g., 001AF43S or 001RE432M).
- Use the rear housing as a template to mark the drilling points on the wall.
- Drill pilot holes at the marked locations.
- Place the sealing gasket between the keypad unit and the mounting surface to ensure IP54 weather protection.
- Secure the keypad unit to the surface using the provided mounting screws. Do not overtighten.
Figure 3.1: Example of the wireless code lock installed on a wall, integrated with an automated gate system.
4. Operating Instructions
The CAME 806SL-0170 allows for secure access via programmable codes. It supports up to 25 memorable codes in both fixed and rolling code modes.
4.1 Keypad Features
- 12 Keys: Numeric keys (0-9), asterisk (*), and hash (#) for code entry.
- Blue Backlight: Provides optimal reading and visibility in low-light conditions. The backlight can be activated by pressing any key.
Figure 4.1: A hand interacting with the keypad, demonstrating the blue backlight feature for improved visibility.
4.2 Programming Access Codes
Refer to the specific instructions for your CAME radio receiver (e.g., 001AF43S or 001RE432M) for detailed steps on pairing the keypad and programming access codes. Generally, the process involves:
- Activating the programming mode on your CAME radio receiver.
- Entering the desired access code (2 to 8 digits) on the 806SL-0170 keypad.
- Confirming the code on the keypad, which sends the signal to the receiver.
- Exiting programming mode on the receiver.
The keypad supports up to 25 unique codes. Ensure codes are kept confidential.
4.3 Using the Keypad for Access
To gain access, simply enter your pre-programmed access code on the keypad. Upon successful entry, the keypad will transmit a signal to the paired CAME receiver, triggering the connected device (e.g., gate, door).
5. Maintenance
5.1 Battery Replacement
The unit is powered by a CR123A battery. When the battery level is low, the keypad's backlight may dim or fail to illuminate, or the transmission range may decrease. To replace the battery:
- Open the rear casing of the keypad unit.
- Remove the old CR123A battery.
- Insert a new CR123A battery, observing correct polarity.
- Securely close the rear casing.
5.2 Cleaning
Clean the keypad surface with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish or electronic components. The IP54 rating ensures protection against dust and splashing water, but avoid direct high-pressure water jets.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Keypad does not respond or backlight is dim. | Low or dead battery. | Replace the CR123A battery (refer to Section 5.1). |
| Keypad enters code but gate/door does not open. | Incorrect code entered. Keypad not paired with receiver. Receiver malfunction or out of range. | Verify the code. Re-pair the keypad with the CAME radio receiver (refer to your receiver's manual). Check receiver's power and antenna. Ensure keypad is within operational range. |
| Intermittent operation. | Weak battery. Radio interference. Keypad too far from receiver. | Replace battery. Identify and remove sources of interference. Relocate keypad closer to the receiver or ensure clear line of sight. |
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | 806SL-0170 |
| Frequency | 433.92 MHz |
| Power Supply | 1 x CR123A Battery |
| Number of Codes | Up to 25 (memorable) |
| Code Length | 2 to 8 digits |
| Protection Rating | IP54 (Dust and splashing water protected) |
| Dimensions (L x W x H) | 8.7 x 7.7 x 7.7 cm |
| Item Weight | 220 g |
| Material | Plastic |
| Colour | Grey |
Figure 7.1: Technical drawing showing the dimensions of the CAME 806SL-0170 keypad unit.
8. Warranty and Support
For warranty information and technical support, please contact your CAME product supplier or visit the official CAME website. Keep your purchase receipt as proof of purchase.
