Introduction
This manual provides essential instructions for the safe and proper assembly, operation, and maintenance of your Kinbor Baby Bathinette Folding Changing Table and Bath Tub Unit. Please read this manual thoroughly before use and retain it for future reference.
Figure 1: Kinbor Baby Bathinette Folding Changing Table and Bath Tub Unit
Safety Information
WARNING: Failure to follow these warnings and instructions could result in serious injury or death.
- Never leave child unattended. Drowning can occur quickly and in as little as 1 inch of water.
- Always keep your child within arm's reach.
- Discontinue use of the changing table when the child begins to push up on hands and knees or has reached 30 lbs (13.6 kg), whichever comes first.
- Ensure all locking mechanisms are engaged before placing a child on the changing table or in the bath tub.
- Do not use this product if it is damaged or broken.
- Keep small parts away from children during assembly and use.
- Always test water temperature before placing child in the bath tub.
- Do not use this product as a sleeping surface.
Setup Instructions
The Kinbor Baby Bathinette is designed for straightforward assembly. Most components are pre-assembled, requiring minimal effort to set up.
- Unfold the Frame: Carefully unfold the main frame of the bathinette until it locks securely into place. Ensure all legs are stable and the frame is fully extended.
- Attach the Bath Tub: Place the bath tub unit onto the designated supports on the frame. Press down firmly until it clicks into position. Verify that the tub is securely attached and does not wobble.
- Install the Changing Pad: Position the changing pad over the bath tub. It should rest securely on the tub's edges. Some models may require attaching with screws; refer to the included hardware for specific instructions.
- Assemble the Storage Tray: Slide the lower storage tray into its designated slots on the frame. Ensure it is level and stable for holding baby essentials.
- Connect the Drainage Hose: Attach the drainage hose to the outlet at the bottom of the bath tub. Ensure a tight connection to prevent leaks. Direct the hose towards a suitable drain when in use.
Figure 2: Fully assembled Kinbor Baby Bathinette with changing pad
Operating Instructions
Using the Changing Table
The elevated design of the changing table provides a comfortable height for parents, reducing strain on the back and knees during diaper changes and dressing.
- Ensure the changing pad is securely placed over the bath tub.
- Always keep one hand on your baby while on the changing table.
- Have all necessary changing supplies (diapers, wipes, cream) within easy reach on the lower storage tray before placing your baby on the pad.
Figure 3: Parent using the changing table feature
Using the Bath Tub
To access the bath tub, gently lift and slide the changing pad to the side. The bath tub is designed for safe and convenient bathing.
- Remove the changing pad and place it in a safe, stable location.
- Ensure the drainage hose is properly connected and directed towards a drain.
- Fill the bath tub with warm water. Always test the water temperature with your elbow or a thermometer before placing your baby in the tub.
- Gently place your baby into the tub, always supporting their head and neck.
- Never leave your baby unattended in the bath tub, even for a moment.
- After bathing, open the drain plug to empty the water.
Figure 4: Parent using the bath tub feature
Using the Storage Tray
The spacious lower tray provides convenient storage for diapers, wipes, towels, and other baby essentials, keeping them organized and within reach.
Figure 5: Storage tray for baby essentials
Maintenance
- Cleaning the Bath Tub: After each use, rinse the bath tub thoroughly with clean water. Use a mild soap and soft cloth for cleaning, then rinse again. Ensure all soap residue is removed.
- Cleaning the Changing Pad: Wipe the changing pad with a damp cloth and mild soap. Air dry completely before next use.
- Frame and Tray: Wipe down the frame and storage tray with a damp cloth as needed. Avoid abrasive cleaners.
- Drying: Ensure all components are completely dry before folding for storage to prevent mold or mildew.
Figure 6: Drainage system for easy cleaning
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit feels unstable after assembly. | Frame not fully locked or components not securely attached. | Ensure the frame is fully unfolded and all locking mechanisms are engaged. Re-check that the bath tub and changing pad are clicked into place. |
| Water leaks from the drainage hose. | Hose not properly attached or drain plug not sealed. | Verify the drainage hose is tightly connected to the tub's outlet. Ensure the drain plug is fully inserted and sealed before filling with water. |
| Changing pad does not sit flat. | Incorrect placement or obstruction. | Ensure the changing pad is correctly aligned with the tub's edges and there are no obstructions underneath. |
Specifications
- Model: B07T6DZ42N
- Item Weight: 20 pounds
- Package Dimensions: 32.68 x 20.87 x 10.24 inches
- Batteries Required: No
- Maximum Weight Capacity (Changing Table): 30 lbs (13.6 kg)
Warranty and Support
For warranty information or product support, please contact the manufacturer directly. Refer to the product packaging or the manufacturer's official website for contact details.
Manufacturer: Levida
For further assistance, please visit the Levida Store on Amazon.