Eapmic 12V 45W RGB IP68 Underwater Pool Light Instruction Manual

1. Important Safety Information

Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or other hazards, and may void the product warranty.

• This product operates on AC12V. Ensure your power supply matches this requirement.
• Installation must be performed by a qualified electrician to prevent electrical hazards.
• A professional LED transformer (AC110V to AC12V 60W) is required. Do not use a halogen bulb transformer.
• Ensure all connections are waterproof and sealed to maintain the IP68 rating.
• Always disconnect power before performing any installation, maintenance, or troubleshooting.
• The light must be fully submerged in water during operation to prevent overheating.

2. Product Overview

The Eapmic 12V 45W RGB IP68 Underwater Pool Light is designed for illuminating swimming pools, bathtubs, jacuzzis, and home aquariums. It features color-changing LED lights controlled by a remote.

Package Contents:

• RGB LED Pool Light (45W)
• RF Remote Controller (battery not included, requires 23A, 12V battery)
• Plastic Bracket
• Explosion Screw Sets

Figure 1: Eapmic 45W Pool Light and included accessories.

Key Features:

• Voltage Input: AC12V
• Wattage: 45W (4500 lumens, 450 LEDs)
• Light Color: RGB (7 fixed colors, 11 changing modes)
• Beam Angle: 120 degrees
• Waterproof Rating: IP68 (fully submersible, epoxy filled)
• Material: ABS+PC (high quality, corrosion and high temperature resistance)
• Power Cord Length: 1.5m
• Dimensions: Ø29.5cm x H6cm
• Working Life: Up to 50,000 hours

Figure 2: High-quality ABS+PC material for durability.

Figure 3: IP68 Repelling Water Design ensures full submersion capability.

3. Installation

Professional installation by a qualified electrician is strongly recommended. Ensure power is disconnected before beginning installation.

1. Prepare Mounting Location: Drill 4 holes for the mounting bracket on the pool wall. The mounting bracket should be installed at a depth of 1.5m to 4m below the water surface.
2. Install Bracket: Securely attach the plastic mounting bracket to the drilled holes using the provided explosion screw sets.
3. Connect Wiring: Connect the light's AC12V power cord to a suitable AC12V power source via a professional LED transformer (AC110V to AC12V 60W). Ensure all electrical connections are properly insulated and waterproofed.
4. Mount Light: Align the pool light with the installed mounting bracket and secure it with screws.
5. Verify Submersion: Ensure the light is fully submerged in water before turning on the power.

Figure 4: Visual guide for installation steps.

4. Operating Instructions

The Eapmic pool light offers multiple color options and lighting modes, controllable via the included RF remote or by cycling power.

Remote Control Operation:

Insert a 23A, 12V battery into the RF remote controller. Point the remote towards the pool light to change settings.

• Power Button: Turn the light ON/OFF.
• Color Selection Buttons: Select from 7 fixed colors (e.g., Red, Green, Blue, Yellow, Purple, Cyan, White).
• Mode Selection Buttons: Cycle through 11 different dynamic lighting modes (e.g., flash, fade, smooth transitions).
• Brightness Adjustment: Adjust the intensity of the light (if available on your remote model).

Switch Control (Power Cycling):

If the remote is unavailable or not preferred, you can cycle through the lighting modes by quickly turning the power to the light OFF and ON again using your pool's main light switch. Each power cycle will advance to the next color or mode.

Figure 5: Available colors and lighting modes.

5. Maintenance

The Eapmic pool light is designed for minimal maintenance due to its durable construction and sealed design.

• Cleaning: Periodically clean the light's surface to remove algae or mineral deposits that may obstruct light output. Use a soft brush or cloth and mild pool-safe cleaning solutions. Do not use abrasive cleaners.
• Inspection: Regularly inspect the power cord and the light housing for any signs of damage, cracks, or wear. If any damage is observed, disconnect power immediately and contact a qualified technician for repair or replacement.
• Water Level: Always ensure the light remains fully submerged in water during operation. Operating the light out of water can lead to overheating and damage.
• Remote Battery: Replace the remote control battery (23A, 12V) as needed if the remote's range or responsiveness decreases.

6. Troubleshooting

If you encounter issues with your Eapmic pool light, refer to the following common troubleshooting steps:

For problems not listed here or if solutions do not resolve the issue, please contact Eapmic customer support.

7. Specifications

8. Warranty and Support

For warranty information, technical support, or any product-related inquiries, please contact Eapmic customer service through the retailer where the product was purchased or visit the official Eapmic website.

Please retain your purchase receipt as proof of purchase for warranty claims.