Introduction
Thank you for choosing the Homelegance Eleonore Queen Panel Bed. This manual provides essential information for the safe assembly, operation, and maintenance of your new bed. Please read these instructions carefully before beginning assembly and retain them for future reference.
The Eleonore Queen Panel Bed features a white high-gloss finish, an opalescent bi-cast vinyl headboard, and integrated LED lighting, designed to complement modern bedroom aesthetics.
Safety Information
Always prioritize safety during assembly and use. Failure to follow these instructions may result in injury or damage to the product.
- Keep all small parts and packaging materials away from children.
- Ensure all connections are securely fastened before use.
- Do not exceed the maximum weight recommendation of 600 lbs.
- Use only the provided hardware for assembly.
- Assembly should be performed by at least two adults.
- Periodically check all bolts and screws to ensure they remain tight.
- Do not stand or jump on the bed.
- This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning).
Package Contents
Your Homelegance Eleonore Queen Panel Bed ships in 3 boxes. Please verify that all components are present before beginning assembly.
Included Components:
- Headboard with LED lighting
- Footboard
- Side Rails (2)
- Slats (4)
- Support Legs
- Assembly Hardware (bolts, screws, washers, Allen wrench)
Note: Mattress is not included.
Assembly Instructions
Follow these steps carefully for proper assembly. It is recommended to assemble the bed in the room where it will be used.
- Unpack Components: Carefully remove all parts from the packaging. Lay them out on a soft, clean surface to prevent scratches.
- Attach Side Rails to Headboard: Align the side rails with the pre-drilled holes on the headboard. Secure them using the provided bolts and washers. Do not fully tighten yet.
- Attach Side Rails to Footboard: Repeat the process for attaching the side rails to the footboard. Ensure the footboard is facing the correct direction.
- Tighten All Connections: Once all four corners are connected, carefully tighten all bolts using the Allen wrench. Do not overtighten.
- Install Support Legs: Attach the central support legs to the cross-slats or central beam, if applicable, following the specific diagrams in your hardware packet.
- Place Slats: Distribute the 4 slats evenly across the bed frame. Secure them to the side rails using the provided screws.
- Connect LED Power (if applicable): Locate the LED power cable from the headboard. Connect it to the power adapter and then to a wall outlet.
Image 1: Overall dimensions of the Eleonore Queen Panel Bed. Length: 86 inches, Width: 63 inches, Height: 55 inches.
Image 2: Side view of the Eleonore Queen Panel Bed, showcasing the panel design and headboard.
Image 3: Front view of the Eleonore Queen Panel Bed, highlighting the headboard and footboard design.
Operating Instructions (LED Lighting)
The Eleonore Panel Bed features integrated LED lighting in the headboard.
- To activate the LED lighting, ensure the bed is properly assembled and the power adapter is plugged into a functional wall outlet.
- The LED lights are typically controlled by a switch located on the headboard or an inline switch on the power cord. Refer to the specific hardware diagram for your model.
- Unplug the power adapter from the wall outlet when the LED lighting is not in use for extended periods.
Image 4: Close-up view of the headboard, showing the integrated LED lighting strip.
Maintenance and Care
Proper care will extend the life and appearance of your Eleonore Panel Bed.
- Cleaning: Wipe surfaces with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals, as these can damage the high-gloss finish and bi-cast vinyl.
- Spills: Blot spills immediately with a clean, dry cloth.
- Sunlight: Avoid prolonged exposure to direct sunlight to prevent fading or discoloration.
- Hardware: Periodically check and tighten all assembly hardware to ensure stability.
- LEDs: LED lights are designed for long life and typically do not require replacement. If issues arise, consult the troubleshooting section.
Image 5: Detail of the opalescent bi-cast vinyl material used in the headboard.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Bed feels wobbly or unstable. | Loose hardware. | Check and tighten all bolts and screws. Ensure slats are properly secured. |
| LED lights not working. | Power cord unplugged, faulty outlet, switch off. | Ensure power adapter is securely plugged into a working outlet. Check the LED switch. |
| Squeaking noises. | Loose connections, friction between components. | Tighten all hardware. Apply a small amount of lubricant (e.g., silicone spray) to contact points if necessary. |
Specifications
- Model: Eleonore
- Size: Queen
- Product Dimensions (L x W x H): 86" x 63" x 55"
- Headboard Size: 63" W x 55" H
- Footboard Size: 63" W x 18" H
- Material: Fabric (75% Polyurethane, 25% Polyester), Foam, Wood
- Finish: White High Gloss
- Special Feature: Integrated LED Lighting
- Maximum Weight Recommendation: 600 lbs
- Assembly Required: Yes
- Included Components: Headboard, Footboard, Side Rails, 4 Slats, Support Legs, Hardware
- Manufacturer: Homelegance
- Brand: Lexicon (as per Amazon listing, but Homelegance is the manufacturer)
- UPC: 782359894355
Warranty and Support
For specific warranty information, please refer to the documentation included with your purchase or contact Homelegance customer support directly. Keep your proof of purchase for warranty claims.
For further assistance, missing parts, or technical support, please contact the manufacturer, Homelegance, or the retailer from whom you purchased the product.