Smeg COLONIALE P875AO Vitroceramic Electric Cooktop User Manual

1. Introduction

This manual provides essential information for the safe and efficient use of your Smeg COLONIALE P875AO Vitroceramic Electric Cooktop. Please read it thoroughly before installation, operation, or maintenance.

The Smeg P875AO cooktop features an anthracite frame and a black ceramic glass surface, controlled by copper-finished knobs. It is designed for integrated installation and offers five radiant heating zones.

Figure 1.1: Top view of the Smeg COLONIALE P875AO Vitroceramic Electric Cooktop. The cooktop features a black ceramic glass surface with five radiant heating zones, which glow red when active. Below the main cooking surface, there are five control knobs with a copper finish, each corresponding to a heating zone. The Smeg logo is visible in the center.

2. Safety Information

Important: Read all instructions before using the appliance to prevent injury or damage.

• Ensure the appliance is properly installed by a qualified technician in accordance with local regulations.
• Do not touch hot surfaces. Always use oven mitts or pot holders.
• Never leave the cooktop unattended during operation, especially when cooking with oil or fat.
• Keep children away from the appliance. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Do not use the cooktop as a work surface or for storage.
• Avoid placing metallic objects such as knives, forks, spoons, and lids on the cooktop surface as they can become hot.
• In case of a crack in the ceramic glass surface, immediately switch off the appliance and disconnect it from the power supply to avoid the possibility of electric shock.
• Ensure adequate ventilation around the appliance.
• The appliance is equipped with overheat protection. If activated, the heating zone will temporarily switch off.
• After use, the ceramic glass surface retains residual heat. The residual heat indicator will illuminate until the surface has cooled to a safe temperature.

3. Setup and Installation

The Smeg P875AO cooktop is designed for built-in installation. It is crucial that installation is performed by a qualified electrician or authorized service technician to ensure compliance with all electrical and safety standards.

3.1 Unpacking

• Carefully remove the cooktop from its packaging.
• Check for any signs of damage during transit. If damage is found, do not install the appliance and contact your retailer.
• Ensure all components listed in the "Included Components" section (see Specifications) are present, including the mounting kit and this user manual.

3.2 Electrical Connection

• The appliance requires a voltage of 380-415 V (220-240 V) and a frequency of 50/60 Hz.
• The connection capacity is 8.60 kW, with a safety rating of 38 A.
• The plug type is Type C/EF - 2 pins (Europlug/FR-DE Hybrid).
• All electrical connections must comply with local wiring regulations.

3.3 Mounting

• Refer to the separate mounting instructions provided with the mounting kit for detailed cutout dimensions and installation procedures.
• Ensure sufficient clearance for ventilation beneath the cooktop.

4. Operating Instructions

Your Smeg P875AO cooktop features five radiant heating zones, each controlled by a dedicated knob.

4.1 Heating Zones Overview

• Rear Left: 1.20 kW, Ø 140 mm
• Front Left: 1.80 kW, Ø 180 mm
• Central: 2.00 kW, 150 x 250 mm (oval zone)
• Rear Right: 2.40 kW, Ø 210 mm
• Front Right: 1.20 kW, Ø 140 mm

4.2 Using the Control Knobs

1. Identify the knob corresponding to the desired heating zone. The layout of the knobs typically mirrors the layout of the heating zones on the cooktop surface.
2. Turn the knob clockwise to activate the heating zone and select a power level. The cooktop offers 6 power levels, ranging from 1 (low heat) to 6 (high heat).
3. The selected heating zone will begin to glow red, indicating it is active and heating.
4. To turn off a heating zone, turn its corresponding knob counter-clockwise back to the '0' position.

4.3 Residual Heat Indicator

After a heating zone is switched off, the residual heat indicator (usually an 'H' or a dot on the cooktop display, or a light near the knob) will remain illuminated. This indicates that the surface is still hot and caution should be exercised. The indicator will turn off once the surface has cooled to a safe temperature.

5. Maintenance and Cleaning

Regular cleaning and maintenance will ensure the longevity and optimal performance of your cooktop.

5.1 Daily Cleaning

• Always ensure the cooktop is cool before cleaning.
• Wipe the ceramic glass surface with a soft cloth or sponge and a mild detergent.
• For stubborn stains or burnt-on food, use a specialized ceramic hob cleaner.
• Rinse thoroughly and dry with a clean cloth to prevent water spots.

5.2 Using the Glass Scraper

A glass scraper is included with your cooktop for removing tough, burnt-on residues. Use it carefully at an angle to avoid scratching the surface. Always follow the scraper manufacturer's instructions.

5.3 Control Knobs

The control knobs can be cleaned with a damp cloth. Do not use abrasive cleaners or immerse them in water.

6. Troubleshooting

Before contacting service, please check the following common issues:

• Cooktop does not turn on:
  • Check if the appliance is properly connected to the power supply.
  • Verify that the circuit breaker has not tripped.
• Heating zone not heating:
  • Ensure the control knob for that zone is turned to a power level greater than '0'.
  • Check if the overheat protection has been activated (the zone will cool down before reactivating).
• Residual heat indicator remains on:
  • This is normal. The indicator will turn off once the surface has cooled sufficiently.
• Unusual noises during operation:
  • Minor expansion and contraction noises are normal during heating and cooling.

If the problem persists after checking these points, disconnect the appliance from the power supply and contact a qualified service technician.

7. Specifications

8. Warranty and Support

For warranty information, please refer to the warranty card included with your product or consult the official Smeg website. Keep your proof of purchase for any warranty claims.

For technical support or service inquiries, please contact your retailer or the authorized Smeg service center in your region. Contact details can typically be found on the Smeg official website or in your product documentation.