Introduction
This manual provides instructions for the NorthStar Nozzle Kit, designed to enhance the functionality of your NorthStar 2-Nozzle Boom Kit (Item# 99900) when used with the NorthStar 10-Gal. Spot Sprayer (Item# 99918). Please read these instructions carefully before installation and operation to ensure safe and effective use.
Safety Information
Always wear appropriate personal protective equipment (PPE) when handling sprayer systems and nozzles, including eye protection and chemical-resistant gloves. Ensure the sprayer system is depressurized and turned off before installing, removing, or cleaning nozzles. Keep all components out of reach of children and pets. Refer to your main sprayer manual for additional safety guidelines.
Package Contents
Verify that all items are present in your NorthStar Nozzle Kit:
- 2 x Hypro 2.0 Red Deflec Tip Nozzles
Image showing two red Hypro 2.0 Deflec Tip nozzles, which are included in the kit. These nozzles are designed for efficient spray distribution.
Setup Instructions
- Preparation: Before beginning installation, ensure the sprayer system is completely turned off and any residual pressure has been safely released.
- Nozzle Attachment: Carefully thread or snap the Hypro 2.0 Red Deflec Tip nozzles onto the designated ports of your NorthStar 2-Nozzle Boom Kit. Ensure each connection is secure and leak-free to prevent product loss and ensure proper spray pattern.
- System Compatibility: This nozzle kit is specifically designed for optimal performance with the NorthStar 2-Nozzle Boom Kit (Item# 99900) and requires a 1 GPM (Gallon Per Minute) pump, such as the one found in the NorthStar 10-Gal. Spot Sprayer (Item# 99918). Using incompatible equipment may result in poor performance or damage.
Operating Instructions
These nozzles are engineered to provide a consistent 105-degree spray pattern, ensuring even distribution of sprayed material over a 6.7-foot wide area.
- Flow Rate: The nozzles are optimized for a 1 GPM pump. Operating with a pump that delivers a significantly different flow rate may alter the spray pattern, coverage, and effectiveness.
- Spray Pattern: The 105-degree spray angle is designed for broad and consistent coverage, ideal for various spraying applications.
- Application: Once the nozzles are correctly installed, operate your NorthStar sprayer system according to its own instruction manual. Observe the spray pattern to ensure desired coverage and adjust sprayer speed or pressure as needed, within the system's capabilities.
Maintenance
Proper maintenance extends the life of your nozzles and ensures consistent performance.
- Cleaning: After each use, thoroughly flush the nozzles with clean water to prevent clogging from chemical residues. For stubborn clogs, carefully remove the nozzle and clean with a soft brush or compressed air. Avoid using metal objects that could damage the nozzle orifice.
- Inspection: Regularly inspect nozzles for signs of wear, damage, or blockages. A worn nozzle tip can lead to an inconsistent spray pattern and reduced efficiency. Replace worn or damaged nozzles promptly to maintain optimal spray performance.
- Storage: Store nozzles in a clean, dry place away from direct sunlight, extreme temperatures, and corrosive chemicals.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Uneven spray pattern | Clogged nozzle orifice, Worn nozzle tip | Clean the nozzle thoroughly, Replace the nozzle if worn |
| Reduced flow from nozzle | Clogged nozzle, Insufficient pump pressure from sprayer | Clean the nozzle, Check the sprayer pump and system for blockages or malfunctions |
| Leaking at nozzle connection | Loose connection, Damaged O-ring or seal | Tighten the connection securely, Inspect and replace the O-ring or seal if damaged |
Specifications
- Model Number: 3562210
- Material: Metal
- Item Dimensions (L x W x H): 0.72 x 0.57 x 0.57 inches
- Exterior Finish: Metal
- Inlet Connection Size: 0.25 Inches
- Inlet Connection Type: Press
- Outlet Connection Type: NPT
- Number of Ports: 2
- Outlet Connection Size: 0.25 Inches
- Item Weight: 0.48 ounces
- Spray Pattern: 105 degrees
- Required Pump Flow: 1 GPM
- Spray Width: 6.7 feet
Warranty Information
For specific warranty details regarding your NorthStar Nozzle Kit, please refer to the documentation provided with your original NorthStar sprayer or contact NorthStar customer support directly. General warranty terms typically cover manufacturing defects for a limited period from the date of purchase.
Customer Support
If you have any questions, require technical assistance, or need to order replacement parts for your NorthStar Nozzle Kit, please visit the official NorthStar website or contact their customer service department. When contacting support, please have your product model number (3562210) readily available to expedite service.
