Black Diamond Spinner Leash Instruction Manual

Introduction

The Black Diamond Spinner Leash is a dual retractable leash system designed to secure ice climbing tools during use. It provides freedom of movement while preventing accidental drops of essential equipment in challenging environments such as steep ice and mixed terrain. This manual provides instructions for the proper setup, operation, and maintenance of your Spinner Leash.

Figure 1: The Black Diamond Spinner Leash. This image displays the Black Diamond Spinner Leash, featuring its dual retractable cords, the central orange swivel mechanism, and the two black tool attachment clips.

Setup

Proper setup ensures the secure attachment and reliable function of your Spinner Leash.

1. Inspect the Leash: Before each use, visually inspect the entire leash system, including the webbing, elastic cords, swivel, and attachment clips, for any signs of wear, cuts, fraying, or damage. Do not use if damage is observed.
2. Attach to Harness: Secure the main loop of the Spinner Leash to a strong, load-bearing point on your climbing harness, such as the belay loop or a dedicated gear loop, using a locking carabiner (not included). Ensure the carabiner is properly locked.
3. Attach to Ice Tools: Connect each of the two reinforced clips at the end of the retractable leashes to the designated attachment points on your ice tools. Ensure the clips are fully closed and secure. These clips are designed for dependable retention during strenuous climbing.
4. Test Connections: Gently pull on each attached tool to confirm that all connections are secure and that the leash retracts and extends smoothly without snagging.

Operating Instructions

The Spinner Leash is designed to provide tool security while allowing for dynamic movement during ice and mixed climbing.

• Freedom of Movement: The dual retractable leash system allows the leashes to stretch and retract smoothly, maintaining freedom of movement for your arms and tools. This is particularly beneficial for high-reach swings and precise tool placements.
• Tangle Prevention: The integrated swivel mechanism is designed to eliminate twisting and tangling of the leashes when you switch hands or match tools. This ensures smooth swings and efficient tool management, reducing distractions during critical maneuvers.
• Tool Security: The primary function of the leash is to prevent the accidental dropping of ice tools. Always ensure tools are properly clipped in before ascending.
• Avoid Over-Extension: While the leashes are designed to extend, avoid pulling them to their absolute maximum length repeatedly or with excessive force, as this can cause premature wear.

Maintenance

Proper maintenance extends the lifespan and ensures the safety of your Spinner Leash.

• Cleaning: If the leash becomes dirty, clean it with mild soap and lukewarm water. Rinse thoroughly with clean water. Do not use harsh chemicals or solvents.
• Drying: Allow the leash to air dry completely in a cool, shaded area away from direct sunlight or heat sources. Do not machine dry.
• Storage: Store the leash in a cool, dry place, away from direct sunlight, chemicals, and sharp objects. Avoid storing it under heavy loads that could compress or damage the elastic components.
• Regular Inspection: Conduct thorough inspections before and after each use. Look for any signs of wear, cuts, abrasions, fraying, deformation of metal parts, or loss of elasticity in the cords. Retire the product immediately if any damage is found or if its integrity is compromised.

Troubleshooting

This section addresses common issues you might encounter with your Spinner Leash.

• Leash Not Retracting Smoothly:
  • Check for dirt or debris in the retraction mechanism. Clean as per maintenance instructions.
  • Ensure the leash is not twisted or tangled around itself or other gear.
  • Inspect for damage to the elastic cords. If elasticity is lost, the product should be retired.
• Tools Feel Loose or Unsecured:
  • Verify that the attachment clips are fully closed and properly engaged with the tool's attachment point.
  • Ensure the main loop is securely attached to your harness with a locked carabiner.
  • Inspect the clips for deformation or damage. If damaged, retire the product.
• Swivel Not Functioning Correctly:
  • Check for any obstructions or debris preventing the swivel from rotating freely.
  • Clean the swivel mechanism.
  • If the swivel is stiff or seized, the product may be damaged and should be retired.

If you experience persistent issues or suspect any component is compromised, discontinue use immediately and contact Black Diamond customer support.

Specifications

Warranty Information

Black Diamond Equipment products are warranted against defects in material or workmanship for the reasonable lifetime of the product. This warranty does not cover normal wear and tear, modifications, improper use, accidents, or neglect. For specific warranty claims or details, please refer to the official Black Diamond website or contact their customer service directly.

Support

For further assistance, technical questions, or to report any issues with your Black Diamond Spinner Leash, please contact Black Diamond Equipment customer support.

• Website: www.blackdiamondequipment.com
• Contact Information: Refer to the "Contact Us" section on the official website for phone numbers, email addresses, and support hours.

Always prioritize safety and consult with experienced professionals if you are unsure about the proper use or maintenance of climbing equipment.