Introduction
The JBL GO2 is a full-featured waterproof portable Bluetooth speaker designed for on-the-go audio. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your device to ensure optimal performance.
Image: Front view of the JBL GO2 speaker in blue, showcasing its compact design and JBL logo.
What's in the Box
Verify that all items are present upon unboxing:
- JBL GO2 Speaker
- Micro USB Cable (for charging)
- Quick Start Guide (this document)
Setup
1. Charging the Speaker
Before first use, fully charge the JBL GO2 speaker. Connect the supplied Micro USB cable to the charging port on the speaker and the other end to a USB power adapter (not included). The charging indicator light will illuminate during charging and turn off when fully charged. A full charge takes approximately 2.5 hours.
Image: Side view of the JBL GO2 speaker, highlighting the Micro USB charging port and 3.5mm auxiliary input, both protected by a waterproof flap.
2. Powering On/Off
Press and hold the power button located on the top of the speaker for approximately 2 seconds to power on or off. A distinct audio cue will indicate the power status.
3. Bluetooth Pairing
- Power on the JBL GO2 speaker. The Bluetooth indicator light will flash blue, indicating it is in pairing mode.
- On your mobile device, navigate to the Bluetooth settings.
- Select "JBL GO2" from the list of available devices.
- Once connected, the Bluetooth indicator light will turn solid blue, and an audio cue will confirm the connection.
4. Auxiliary Connection
For devices without Bluetooth, connect an audio cable (not included) from your device's headphone jack to the 3.5mm auxiliary input port on the JBL GO2 speaker. The speaker will automatically switch to auxiliary mode.
Operating
1. Music Playback
After connecting via Bluetooth or auxiliary cable, begin playing audio from your source device. Use the controls on your device or the speaker to manage playback.
2. Volume Control
Adjust the volume using the '+' and '-' buttons located on the top of the speaker. You can also control the volume from your connected device.
Image: Top view of the JBL GO2 speaker, showing the power, Bluetooth pairing, volume up, volume down, and play/pause/speakerphone buttons.
3. Speakerphone Function
The JBL GO2 features a built-in noise-cancelling speakerphone. When a call is received while connected via Bluetooth:
- Press the play/pause button once to answer an incoming call.
- Press the play/pause button once again to end the call.
- Press and hold the play/pause button to reject an incoming call.
4. Waterproof Usage (IPX7)
The JBL GO2 is IPX7 waterproof, meaning it can be submerged in water up to 1 meter (3 feet) for up to 30 minutes. Ensure the charging port and auxiliary input port covers are securely closed before exposing the speaker to water.
Important:
- Do not expose the speaker to salt water or other liquids.
- Always ensure the port covers are sealed to maintain waterproofing.
Maintenance
1. Cleaning
Clean the speaker with a soft, damp cloth. Do not use abrasive cleaners or solvents. For stubborn dirt, a mild soap solution can be used, followed by rinsing with fresh water if the port covers are sealed.
2. Storage
Store the speaker in a cool, dry place away from direct sunlight and extreme temperatures. If storing for an extended period, charge the battery periodically to maintain its lifespan.
3. Post-Water Exposure Care
After exposure to water, gently shake the speaker to remove excess water from the grille and ports. Allow it to air dry completely before charging or connecting any cables.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Speaker does not power on | Battery is depleted | Charge the speaker using the Micro USB cable. |
| No sound | Volume is too low or muted; Device not connected | Increase volume on speaker and source device; Ensure proper Bluetooth or auxiliary connection. |
| Bluetooth pairing fails | Speaker not in pairing mode; Device too far; Interference | Ensure speaker is in pairing mode (flashing blue light); Move device closer; Turn off other Bluetooth devices. |
| Poor audio quality via Bluetooth | Device too far; Obstructions; Low battery | Move device closer to speaker; Remove obstructions; Charge the speaker. |
Specifications
| Feature | Detail |
|---|---|
| Model Name | Go 2 |
| Wireless Communication Technology | Bluetooth |
| Connectivity Technology | Auxiliary, Bluetooth |
| Water Resistance Level | IPX7 Waterproof |
| Playtime | Up to 5 hours (varies by volume level and audio content) |
| Charging Time | Approximately 2.5 hours |
| Speaker Maximum Output Power | 5 Watts |
| Frequency Response | 20 KHz |
| Product Dimensions (D x W x H) | 3.1" x 8.6" x 7.1" (approx. 7.9cm x 21.8cm x 18cm) |
| Item Weight | 6.5 Ounces (approx. 184 grams) |
| Input Voltage | 5 Volts |
| Bluetooth Range | 10 Meters (33 feet) |
| Special Features | Built-in Microphone, Waterproof |
Warranty and Support
Warranty Information
The JBL GO2 speaker comes with a limited warranty. Please refer to the warranty card included with your product or visit the official JBL website for detailed terms and conditions regarding warranty coverage and duration.
Customer Support
For further assistance, technical support, or service inquiries, please visit the official JBL support website or contact their customer service department. Contact information can typically be found on the JBL website or in the product packaging.
