XLC Ks-r02 Rear Kickstand Instruction Manual

1. Introduction

Thank you for choosing the XLC Ks-r02 Rear Kickstand. This kickstand is designed to provide stable support for your bicycle when parked. It features a robust aluminum construction and is adjustable to fit various wheel sizes. Please read this manual carefully before installation and use to ensure proper function and safety.

2. Safety Information

• Always ensure the kickstand is fully deployed and stable before leaving your bicycle unattended.
• Do not sit on the bicycle or apply excessive weight to it when the kickstand is deployed, as this may cause damage or instability.
• Regularly check all mounting screws for tightness. Loose screws can lead to kickstand failure and potential injury.
• Ensure the kickstand does not interfere with the bicycle's moving parts, such as the chain, pedals, or rear wheel, during operation or riding.
• Keep children and pets away from the bicycle when the kickstand is in use.

3. Package Contents

Verify that all components are present before beginning installation:

• 1 x XLC Ks-r02 Rear Kickstand
• Mounting Screws (pre-attached or separate)

Image 1: XLC Ks-r02 Rear Kickstand. This image displays the kickstand in its retracted position, highlighting its aluminum construction and the mounting plate designed for the bicycle's rear frame.

4. Setup and Installation

The XLC Ks-r02 kickstand is designed for mounting on the bicycle's rear frame end. It is suitable for bicycles with wheel sizes ranging from 26 to 29 inches, including 27, 27.5, and 27.5+.

Tools Required:

• Appropriate Allen key or wrench for mounting screws (not included).

Installation Steps:

1. Identify Mounting Location: Locate the designated mounting area on your bicycle's rear frame end. This is typically near the rear axle, often with pre-drilled holes or a flat plate for kickstand attachment.
2. Position the Kickstand: Place the kickstand's mounting plate against the frame. Ensure the kickstand arm is oriented correctly, pointing towards the rear of the bicycle.
3. Attach with Screws: Insert the provided mounting screws through the kickstand's mounting plate and into the frame's attachment points.
4. Tighten Screws: Using the appropriate tool, securely tighten the mounting screws. Do not overtighten, but ensure the kickstand is firmly attached and does not wobble.
5. Adjust Length: The kickstand features an adjustable length mechanism. Loosen the adjustment screw (usually a small bolt on the lower part of the kickstand leg), extend or retract the leg to achieve the desired length for your bicycle's wheel size and ground clearance, then securely tighten the adjustment screw. The bicycle should stand upright and stable when the kickstand is deployed.
6. Check Clearance: With the kickstand retracted, ensure it does not interfere with pedaling, the chain, or the rear wheel during riding. Adjust its position slightly if necessary, then re-tighten all screws.

5. Operating Instructions

Deploying the Kickstand:

To park your bicycle, gently push the kickstand leg downwards and forwards with your foot until it locks into its fully extended position. Ensure the bicycle is stable before releasing it.

Retracting the Kickstand:

Before riding, use your foot to push the kickstand leg backwards and upwards until it locks into its fully retracted position, parallel to the bicycle's chainstay. Ensure it is securely retracted and does not interfere with riding.

6. Maintenance

• Regular Cleaning: Clean the kickstand periodically with a damp cloth to remove dirt and grime. Avoid harsh chemicals that may damage the finish.
• Check Fasteners: Routinely inspect all mounting screws and the adjustment screw for tightness. Tighten any loose fasteners to prevent the kickstand from shifting or detaching.
• Lubrication: Apply a small amount of bicycle-specific lubricant to the pivot points of the kickstand mechanism if it becomes stiff or squeaky.
• Inspect for Damage: Check the kickstand for any signs of bending, cracks, or other damage. Replace the kickstand if it is damaged to ensure safe operation.

7. Troubleshooting

• Kickstand is loose: Check and tighten all mounting screws. Ensure the mounting plate is flush against the frame.
• Bicycle is unstable when parked: Adjust the kickstand length. Ensure the ground surface is level. Verify the kickstand is fully deployed and locked.
• Kickstand interferes with riding: Ensure the kickstand is fully retracted and locked. Check for proper clearance from the chain, pedals, and wheel. Re-adjust mounting position slightly if possible.
• Kickstand is difficult to deploy/retract: Clean the pivot points and apply a small amount of lubricant. Check for any obstructions or damage.

8. Specifications

9. Warranty and Support

For warranty information or technical support, please refer to the documentation provided with your purchase or visit the official XLC website. Keep your proof of purchase for any warranty claims.