1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Came VER PLUS - VER10DMS 24V Garage Door Automation Kit. This system is designed to automate sectional and up-and-over garage doors, offering enhanced convenience and security. Please read this manual thoroughly before proceeding with installation or operation to ensure proper functioning and safety.
2. Safety Information
Important Safety Instructions:
- Installation must be performed by qualified personnel in compliance with local electrical and safety regulations.
- Disconnect power before performing any maintenance or repair work.
- Keep children and pets away from the garage door area, especially during operation.
- Do not operate the door if any part of the system is damaged or malfunctioning.
- Ensure all safety devices (e.g., photocells) are correctly installed and functioning.
- The emergency release mechanism should be accessible and understood by all users.
- This product is designed for garage door automation only. Do not use for other purposes.
3. Package Contents
Verify that all components listed below are present in your package:
- 1x 801MV-0010 VER10DMS Automation Unit: Complete with control panel and encoder for sectional and up-and-over doors.
- 1x AF43S Radio Frequency Board: Plug-in board for radio communication.
- 1x 806TS-0121 TOPD4RBS Transmitter: Rolling code, dual-frequency, quad-channel remote control (blue).
- 1x TOP-A433N Antenna: Tuned 433 MHz antenna.
- 1x Antenna Cable.
Image 1: Overview of the Came VER PLUS - VER10DMS 24V Garage Door Automation Kit components.
4. Setup and Installation
The installation process requires careful attention to detail. It is recommended that installation be carried out by a professional.
4.1 Mounting the Automation Unit
- Fix the automation unit directly onto the transmission guide of your garage door. Ensure it is securely fastened and aligned.
- The system operates on 24V DC, ensuring enhanced safety and reliability.
4.2 Electrical Connections
- The electronic board features separate terminal blocks to facilitate easy and organized wiring.
- Connect the power supply, motor, and safety accessories according to the wiring diagram provided in the full technical manual (not included here).
- Install the AF43S radio frequency board into its designated slot on the control unit.
- Connect the TOP-A433N antenna using the provided antenna cable to optimize remote control signal reception.
4.3 Initial Configuration
- Use the external display buttons on the control unit to navigate through the installation and diagnostic phases.
- The system supports memorization of up to 250 different users. Refer to the full manual for programming user remotes.
- The integrated radio decoding supports Rolling code and Key Code (Twin) for secure communication.
- For RIO System 2.0 wireless safety accessories, use the 806SS-0040 accessory for management.
- CAME keypads can be managed via the R800 board, and transponder selectors can be connected using the R700 accessory.
- The system is prepared for the CAME KEY accessory and cloud connection via CAME Connect for advanced features.
5. Operating Instructions
5.1 Standard Operation
- To open or close the garage door, press the corresponding button on your 806TS-0121 TOPD4RBS remote transmitter.
- The door will move smoothly along the silent and reliable belt or chain sliding guides.
- Pressing the button again during operation will stop the door. A subsequent press will reverse its direction.
5.2 Emergency Operation
- In case of a power outage, the system is designed for emergency operation.
- Locate the external cord release mechanism. Pull the cord to disengage the motor and manually open or close the garage door. This mechanism is applicable to the door's handle-lock system.
- Ensure the emergency release is re-engaged once power is restored or manual operation is no longer needed.
6. Maintenance
Regular maintenance ensures the longevity and safe operation of your garage door automation system.
- Monthly: Inspect the garage door's moving parts (springs, cables, rollers, hinges) for wear or damage. Ensure they are properly lubricated.
- Quarterly: Check the functionality of safety features, such as photocells and the auto-reverse mechanism. The door should reverse if it encounters an obstruction.
- Annually: Have the system inspected by a qualified technician. Check all electrical connections for tightness and signs of corrosion.
- Keep the automation unit and guides clean and free from debris.
- Do not attempt to repair electrical components yourself. Contact a qualified technician.
7. Troubleshooting
This section addresses common issues you might encounter. For more complex problems, consult a professional technician.
| Problem | Possible Cause | Solution |
|---|---|---|
| Door does not move. | No power; remote battery dead; safety sensors obstructed; emergency release engaged. | Check power supply; replace remote battery; clear sensor path; disengage emergency release. |
| Remote control not working. | Battery dead; out of range; remote not programmed. | Replace battery; move closer to antenna; reprogram remote (refer to full manual). |
| Door reverses unexpectedly. | Obstruction in door path; safety sensor misalignment; force settings too sensitive. | Remove obstruction; align safety sensors; adjust force settings (refer to full manual). |
| Unusual noises during operation. | Lack of lubrication; worn parts; loose components. | Lubricate moving parts; inspect for worn or loose components and tighten/replace as needed. |
8. Specifications
| Feature | Detail |
|---|---|
| Model | VER10DMS |
| Brand | Came |
| Power Supply | 24V DC |
| Force | 1000N (for sectional and up-and-over doors) |
| User Memory | Up to 250 users |
| Radio Frequency | 433 MHz (with TOP-A433N antenna) |
| Remote Control | 806TS-0121 TOPD4RBS (Rolling code, dual-frequency, quad-channel) |
| Batteries Included | No |
| Item Weight | 4 Kilograms |
| ASIN | B07S6C9D4H |
| First Available | May 24, 2019 |
9. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or visit the official Came website. Keep your proof of purchase for warranty claims.
Official Came Website: www.came.com
