1. Introduction
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Faber 152 SRM LG/X A90 built-in kitchen hood. Please read these instructions carefully before using the appliance and retain them for future reference.
The Faber 152 SRM LG/X A90 is a 90cm wide built-in hood designed for integration into kitchen cabinetry, featuring electromechanical controls, LED lighting, and metallic grease filters.
2. Safety Information
General Safety:
- Ensure the electrical installation complies with local regulations.
- Do not allow children to operate the appliance.
- Regularly clean the grease filters to prevent fire hazards.
- Do not flambé under the range hood.
- Ensure adequate ventilation in the room when the hood is used simultaneously with other gas or fuel-burning appliances.
Electrical Safety:
- Before any cleaning or maintenance, disconnect the hood from the main power supply.
- If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
3. Product Components
The Faber 152 SRM LG/X A90 built-in hood includes the following key components:
- Motor: Single motor for extraction.
- Controls: Electromechanical push-button controls.
- Lighting: Integrated LED lighting.
- Grease Filters: Metallic filters, designed for easy removal and cleaning.
- Air Outlet: 120 mm diameter for ducting.
Figure 1: The Faber 152 SRM LG/X A90 Built-in Hood seamlessly integrated into a modern white kitchen cabinet, with its front panel slightly open to reveal the controls and metallic filters.
Figure 2: An angled view of the Faber 152 SRM LG/X A90 Built-in Hood, showcasing its metallic finish, control panel, and the grid pattern of the grease filters.
Figure 3: Another view of the Faber 152 SRM LG/X A90 Built-in Hood, installed within a light wood kitchen cabinet, demonstrating its discreet integration.
4. Setup and Installation
The Faber 152 SRM LG/X A90 is designed for built-in installation within a kitchen cabinet. Professional installation is highly recommended to ensure proper function and safety.
Key Installation Considerations:
- Mounting Type: Built-in.
- Width: 900 mm.
- Air Outlet Diameter: 120 mm.
- Ensure sufficient clearance between the cooking surface and the hood as per local regulations and manufacturer guidelines.
- Proper ducting is crucial for effective extraction. Use rigid ducts where possible.
Figure 4: A technical diagram illustrating the dimensions and recommended installation points for the Faber 152 SRM LG/X A90 Built-in Hood, including measurements for cabinet integration and air duct connection.
5. Operating Instructions
The hood is operated using electromechanical push-button controls located on the front panel.
- Power On/Off: Press the main power button to turn the hood on or off.
- Fan Speed Selection: Select from three available fan speeds (1, 2, 3) using the corresponding buttons. Higher speeds provide greater extraction power.
- Light On/Off: Press the light button to activate or deactivate the LED lighting.
Performance Overview:
| Speed | Suction Capacity (IEC) | Pressure (Pa) | Power Consumption (W) | Noise Level (dB) |
|---|---|---|---|---|
| 1 | 115 m³/h | 190 | 80 | 52 |
| 2 | 160 m³/h | 310 | 95 | 59 |
| 3 | 225 m³/h | 370 | 115 | 68 |
6. Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your hood.
- Cleaning Metallic Grease Filters: The metallic grease filters should be cleaned regularly (approximately every 2 months, or more frequently with heavy use). They can be washed by hand with hot water and mild detergent or in a dishwasher on a low-temperature cycle. Ensure they are completely dry before re-installing.
- Cleaning the Hood Surface: Clean the exterior surfaces of the hood with a soft cloth and a non-abrasive cleaner. Avoid using harsh chemicals or abrasive materials that could damage the finish.
- LED Lighting: LED lights are long-lasting and generally do not require replacement. If a light fails, contact qualified service personnel.
7. Troubleshooting
If you encounter issues with your hood, refer to the following common problems and solutions:
- Hood not turning on: Check if the hood is properly connected to the power supply. Verify the circuit breaker.
- Poor suction: Ensure the grease filters are clean. Check for obstructions in the ducting system. Verify that the fan speed is set appropriately for the cooking task.
- Excessive noise: Ensure the hood is securely mounted. Check for loose components or obstructions in the fan.
- Lights not working: Check if the light button has been pressed. If individual LEDs are out, professional service may be required.
For problems not listed here or if solutions do not resolve the issue, contact Faber customer support or a qualified technician.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | FABER |
| Model | 152 SRM LG/X A90 |
| Manufacturer Reference | 315.0547.805 VE19GZ |
| ASIN | B07S63Z3P |
| Control Type | Electromechanical Push-button |
| Lighting Type | LED |
| Filter Type | Metallic Grease Filters |
| Item Shape | Pyramid (internal structure) |
| Ventilation Type | Ducted |
| Hood Design | Built-in Hood |
| Width | 900 mm |
| Air Outlet Diameter | 120 mm |
| Material | Steel Alloy |
| Color | Light Grey |
| Energy Efficiency Class | D |
| Components Included | Steel grille, metallic grease filters |
Figure 5: The EU Energy Label for the Faber 152 SRM LG/X A90 Built-in Hood, indicating an energy efficiency class of D and other performance metrics such as noise level and annual energy consumption.
9. Warranty and Support
For warranty information, please refer to the documentation provided with your product or contact Faber customer service directly. Keep your proof of purchase for warranty claims.
For technical support, spare parts, or service requests, please contact your local Faber authorized service center or visit the official Faber website.
