Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Puig V-Tech Line Touring Windshield, model 1295F. This windshield is designed for specific Honda Forza models to enhance riding comfort and aerodynamics.
Please read these instructions thoroughly before proceeding with installation or use to ensure proper fitment and safe operation.
Safety Information
- Always wear appropriate personal protective equipment during installation.
- Ensure the motorcycle is stable and turned off before beginning any work.
- If you are unsure about any step, consult a qualified mechanic.
- Do not overtighten fasteners, as this may damage components.
- Regularly inspect the windshield and mounting hardware for security and wear.
Compatibility
This Puig V-Tech Line Touring Windshield (Model 1295F) is compatible with the following motorcycle models:
- Honda Forza 125: 2015, 2016, 2017, 2018, 2019, 2020
- Honda Forza 300: 2018, 2019, 2020
Note: Compatibility is crucial for proper fitment and performance. Verify your motorcycle's make, model, and year before installation.
Setup and Installation
The installation process typically involves removing the original windshield and mounting the new Puig windshield using the provided hardware. Specific steps may vary slightly depending on your motorcycle's exact configuration.
Required Tools (Not Included):
- Screwdriver set (Phillips and/or flathead, as needed)
- Hex key set (Allen wrenches)
- Torque wrench (recommended for precise fastening)
- Soft cloth to protect surfaces
Installation Steps:
- Prepare the Motorcycle: Park the motorcycle on a stable, level surface. Turn off the engine and remove the key.
- Remove Original Windshield: Carefully locate and remove the screws or fasteners securing the original windshield to the motorcycle. Keep track of all original hardware.
- Position the Puig Windshield: Align the Puig V-Tech Line Touring Windshield with the mounting points on your motorcycle.
- Install Mounting Hardware: Use the provided Puig hardware (if applicable) or the original hardware (if instructed) to secure the new windshield. Start all fasteners by hand to avoid cross-threading.
- Tighten Fasteners: Gradually tighten all fasteners evenly. If using a torque wrench, refer to your motorcycle's service manual for recommended torque specifications for windshield mounting bolts. Avoid overtightening.
- Final Inspection: Gently shake the windshield to ensure it is securely mounted and does not wobble. Check for any gaps or misalignments.
Image: Puig V-Tech Line Touring Windshield 1295F mounted on a Honda Forza motorcycle. This image illustrates the appearance of the dark smoked windshield after installation.
Operation and Use
The Puig V-Tech Line Touring Windshield is designed to improve aerodynamic protection and riding comfort. Once installed, no specific operational steps are required beyond regular motorcycle operation.
- Enhanced Protection: The touring design offers increased wind and weather protection compared to standard windshields.
- Visibility: The dark smoked tint provides a stylish appearance. Ensure visibility is not compromised, especially during low-light conditions.
Care and Maintenance
Proper care will extend the life and maintain the clarity of your Puig windshield.
- Cleaning: Clean the windshield regularly with a soft cloth and mild soap and water. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the acrylic material.
- Drying: Dry with a clean, soft microfiber cloth to prevent water spots and streaks.
- Inspection: Periodically check all mounting bolts and hardware for tightness. Vibrations from riding can sometimes loosen fasteners.
- Scratch Prevention: Avoid wiping the windshield when dry or with dirty cloths, as this can cause scratches.
Troubleshooting
If you encounter issues with your Puig V-Tech Line Touring Windshield, consider the following common solutions:
| Issue | Possible Cause | Solution |
|---|---|---|
| Windshield wobbles or vibrates | Loose mounting bolts | Check and tighten all mounting bolts securely. |
| Excessive wind noise or buffeting | Incorrect installation or specific rider/motorcycle dynamics | Re-verify installation steps. Ensure all components are correctly aligned. Windshield performance can be subjective; minor adjustments to riding position may help. |
| Scratches or haziness on surface | Improper cleaning methods or abrasive contact | Use only soft cloths and mild soap for cleaning. Avoid dry wiping. Minor scratches may be polished with specialized acrylic polish. |
Specifications
| Feature | Detail |
|---|---|
| Model: | 1295F |
| Brand: | Puig |
| Material: | Acrylic |
| Color: | Dark Smoked |
| Item Weight: | 2.03 pounds (approx. 0.92 kg) |
| Product Dimensions: | 29.13 x 15.75 x 0.02 inches (approx. 74 x 40 x 0.05 cm) |
| Item Thickness: | 4 Millimeters |
| Vehicle Service Type: | Motorcycle |
| Position: | Front |
Warranty and Support
For information regarding product warranty, returns, or technical support, please contact Puig directly or the authorized retailer from whom you purchased this product.
Keep your proof of purchase for any warranty claims.
Manufacturer: Puig
Website: www.puig.tv
