1. Introduction
This manual provides essential information for the safe and effective installation and use of your UNIVERSALE 2200W Double Oven Heating Element. This replacement part is designed for various Beko and Blomberg oven models. Please read these instructions carefully before proceeding with installation or maintenance.
For a list of compatible models, please refer to the product description or contact customer support with your oven's model number.
2. Safety Information
WARNING: Electrical shock hazard. Always disconnect power to the appliance before servicing. Failure to do so can result in serious injury or death.
- Installation should only be performed by a qualified technician or a person with adequate electrical knowledge and experience.
- Ensure the oven is completely disconnected from the main power supply before beginning any work.
- Wear appropriate personal protective equipment, including gloves and eye protection.
- Verify that the replacement element's specifications (voltage, wattage) match your oven's requirements.
- Do not operate the oven if the heating element is damaged or improperly installed.
3. Package Contents
- 1 x UNIVERSALE Double Oven Heating Element 2200W
Inspect the element upon receipt for any signs of damage. If damaged, do not install and contact your supplier immediately.
4. Specifications
| Brand | UNIVERSALE |
| Power | 2200 Watts |
| Dimensions (Approximate) | Width: 335 mm, Depth (with contacts): 357 mm, Drill hole: 347 mm |
| Fixing Hole Spacing | 120 mm (center to center) |
| Flange Length | 100 mm |
| Flange Hole Spacing | 85 mm (center to center) |
| ASIN | B07RWPTHQ1 |
Image 1: UNIVERSALE 2200W Double Oven Heating Element. This image shows the heating element, typically a coiled metal tube, with electrical terminals at one end, designed for installation in an oven.
5. Installation Instructions
Important: Always ensure the oven is disconnected from the power supply before starting installation. If you are unsure about any step, consult a qualified appliance technician.
- Disconnect Power: Turn off the circuit breaker supplying power to your oven. Verify power is off using a voltage tester.
- Access the Element: Depending on your oven model, you may need to remove the oven door, racks, or back panel to access the heating element. Refer to your oven's specific service manual for detailed access instructions.
- Remove Old Element: Carefully disconnect the electrical wires from the old heating element. Note their positions for re-connection. Unscrew any mounting screws or clips holding the old element in place and gently pull it out.
- Install New Element: Insert the new UNIVERSALE heating element into the oven cavity, aligning it with the mounting holes. Secure it with the screws or clips removed earlier.
- Connect Wiring: Reconnect the electrical wires to the terminals of the new heating element in the same configuration as the old one. Ensure connections are secure.
- Reassemble Oven: Replace any panels, racks, or the oven door that were removed.
- Test: Restore power to the oven at the circuit breaker. Turn on the oven to a low temperature setting and observe the element to ensure it heats up correctly. Check for any unusual smells or sounds.
If the element does not heat or if you notice any issues, immediately disconnect power and re-check your installation or consult a professional.
6. Operating Instructions
Once the new heating element is correctly installed and tested, your oven should function as normal. Refer to your oven's original user manual for specific operating instructions, temperature settings, and cooking modes.
During the first few uses, a slight burning smell may occur. This is normal and is due to protective coatings on the new element burning off. Ensure adequate ventilation during this period.
7. Maintenance
The heating element itself requires no specific maintenance. To ensure optimal performance and longevity of your oven:
- Regularly clean the oven interior according to your oven manufacturer's instructions.
- Avoid spilling liquids directly onto the heating element.
- Do not use abrasive cleaners or sharp objects near the element, as this can cause damage.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Oven not heating | No power to oven, faulty wiring connection, element not fully seated. | Check circuit breaker. Verify all electrical connections are secure. Ensure element is correctly installed. |
| Element not glowing evenly | Minor manufacturing variation (usually normal), partial damage. | Observe for a few cycles. If performance is affected or element is visibly broken, replace. |
| Burning smell during first use | Protective coatings burning off. | This is normal. Ensure good ventilation. Smell should dissipate after a few uses. |
If troubleshooting steps do not resolve the issue, or if you suspect a more serious problem, contact a qualified appliance repair technician.
9. Warranty and Support
Information regarding specific warranty terms for this UNIVERSALE heating element is not available in the product details. Please retain your proof of purchase.
For any questions, compatibility checks, or support regarding this product, please contact the seller directly through your purchase platform. When contacting support, please provide your product's ASIN (B07RWPTHQ1) and your oven's model number.
You can also visit the seller's page for more information: SAVI SRL Seller Page
