AT&T CL82257

AT&T CL82257 DECT 6.0 Cordless Phone System User Manual

Model: CL82257 | Brand: AT&T

1. Getting Started

1.1 Package Contents

Verify that your package contains the following items:

  • AT&T CL82257 Base Unit
  • Two (2) Cordless Handsets
  • Two (2) Handset Chargers
  • Two (2) Power Adapters for Base Unit and Chargers
  • One (1) Telephone Line Cord
  • Two (2) Ni-MH Battery Packs
  • Two (2) Battery Compartment Covers

1.2 Battery Installation

Before using the phone, install the battery pack in each cordless handset.

  1. Open the battery compartment cover on the back of the handset.
  2. Plug the battery pack connector securely into the jack inside the compartment.
  3. Place the battery pack with the label UP as indicated.
  4. Close the battery compartment cover.
  5. Place the handset in the charger to charge for at least 16 hours before first use.
AT&T CL82257 Handset with battery compartment visible

Image: A cordless handset with its battery compartment open, showing the battery pack being inserted. This illustrates the battery installation process.

1.3 Base Unit and Charger Connection

Connect the base unit and chargers to power and the telephone line.

  1. Plug one end of the telephone line cord into the TEL LINE jack on the back of the base unit.
  2. Plug the other end of the telephone line cord into a telephone wall jack.
  3. Plug the small end of the base unit power adapter into the POWER jack on the back of the base unit.
  4. Plug the large end of the base unit power adapter into an electrical outlet not controlled by a wall switch.
  5. For each charger, plug the small end of the charger power adapter into the POWER jack on the back of the charger.
  6. Plug the large end of the charger power adapter into an electrical outlet not controlled by a wall switch.
AT&T CL82257 Base Unit and Handset Chargers connected to power and telephone line

Image: The AT&T CL82257 base unit and two handsets in their respective chargers. The base unit shows connections for the telephone line and power adapter, illustrating proper setup.

1.4 Handset Registration

Your handsets are pre-registered to the base unit. If a handset displays "To register HS, see manual" or if you purchase additional handsets, you will need to register them.

  1. Place the unregistered handset in the base unit charger.
  2. Press and hold the FIND HS button on the base unit for about 4 seconds until the IN USE light on the base unit turns on.
  3. While the IN USE light is on, press the # key on the handset.
  4. The handset will display "Registering..." and then "Handset Registered" when complete.

2. Basic Operations

2.1 Making and Receiving Calls

To make a call:

  • Press PHONE or SPEAKER.
  • Dial the telephone number.

To receive a call:

  • When the phone rings, press PHONE or SPEAKER.

To end a call:

  • Press OFF or place the handset in the charger.

2.2 Digital Answering System

The answering system can record up to 22 minutes of messages, announcements, and memos. It features a voice guide for easy setup and operation.

  • To turn on/off: Press ANS ON/OFF on the base unit or use the handset menu.
  • To play messages: Press PLAY/STOP on the base unit or select "Play messages" from the handset menu.
  • To delete messages: During playback, press DELETE on the base unit or select "Delete all old" from the handset menu.

2.3 Smart Call Blocker

The Smart Call Blocker helps screen unwanted calls. It can block up to 1,000 names and numbers.

  • To block a call during a call: Press CALL BLOCK on the handset.
  • To block a number from Caller ID history: Navigate to the desired entry in the Caller ID log, then press MENU/SELECT and choose "Block number".
  • To review blocked numbers: Access the Smart Call Blocker menu via the handset.

2.4 Intercom

You can use the handsets to communicate with each other.

  • Press INT on the handset.
  • If you have multiple handsets, dial the number of the desired handset (e.g., 2 for handset 2).
  • The other handset will ring. To answer, press PHONE or SPEAKER.

2.5 Caller ID

The phone stores the Caller ID information of the last 50 incoming calls.

  • Press CID on the handset to review the Caller ID log.
  • Use the UP or DOWN arrow keys to scroll through entries.
  • To dial a number from the Caller ID log, press PHONE or SPEAKER when the desired entry is displayed.

3. Care and Maintenance

Proper care ensures the longevity of your phone system.

  • Cleaning: Clean the phone with a soft, slightly damp cloth. Do not use cleaning sprays or harsh chemicals.
  • Battery Care: To maintain optimal battery performance, avoid overcharging for extended periods once fully charged. If the phone will not be used for a long time, remove the batteries.
  • Environmental Conditions: Keep the phone away from excessive heat, direct sunlight, and moisture. Do not immerse any part of the phone in water.
  • Avoid Interference: Place the base unit away from other electronic devices such as computers, televisions, and microwave ovens to prevent interference.

4. Troubleshooting Guide

If you experience issues with your phone system, refer to the table below for common problems and solutions.

ProblemSolution
No dial tone
  • Ensure the telephone line cord is securely connected to the base unit and wall jack.
  • Verify the base unit power adapter is plugged into a working electrical outlet.
  • Check if other phones on the same line are working.
Handset not charging
  • Ensure the handset is properly seated in the charger.
  • Verify the charger power adapter is plugged into a working electrical outlet.
  • Clean the charging contacts on the handset and charger with a dry cloth.
  • Check battery pack connection inside the handset.
Poor sound quality / Static
  • Move the handset closer to the base unit.
  • Relocate the base unit away from other electronic devices (e.g., microwave ovens, computers).
  • Check the telephone line cord for damage.
Handset displays "To register HS, see manual"
  • Follow the handset registration steps in Section 1.4.
Answering system not recording messages
  • Ensure the answering system is turned ON.
  • Check if the memory is full; delete old messages if necessary.

5. Technical Specifications

  • Technology: DECT 6.0 Digital technology
  • Expandability: Up to 12 handsets (CL80107 accessory handset)
  • Answering System: Digital, up to 22 minutes recording time
  • Caller ID Memory: 50 names and numbers
  • Smart Call Blocker Memory: Up to 1,000 names and numbers
  • Display: Backlit keypad and high-contrast LCD
  • Dimensions (Base Unit): 6.3 x 3.96 x 7.26 inches (L x W x H)
  • Item Weight: Approximately 1.87 pounds
  • Power: AC power adapters for base and chargers

6. Warranty Information

This product is offered as an Amazon Renewed item. Amazon Renewed products are professionally inspected and tested to work and look like new. They are eligible for replacement or refund under the Amazon Renewed Guarantee if you are not satisfied with your purchase. Please refer to the Amazon Renewed Guarantee terms and conditions for specific details regarding coverage and duration.

7. Customer Support

For technical assistance, troubleshooting beyond this manual, or warranty claims related to your Amazon Renewed AT&T CL82257 phone system, please contact Amazon Renewed customer support. You can typically find support contact information through your Amazon order history or the Amazon Renewed program page.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.