Aqua Select Anti-Slip In-Pool Steps Instruction Manual

1. Introduction

Thank you for choosing Aqua Select Anti-Slip In-Pool Steps. This manual provides essential information for the safe and efficient use of your new pool steps. Please read all instructions carefully before assembly and installation to ensure proper setup and to prevent injury or damage.

These steps are designed to provide safe and easy entry and exit for above-ground swimming pools. They feature textured, non-slip treads for enhanced safety and slats in the back to promote water flow and limit unwanted growth. The system is designed to be mounted to pool decks between 48 and 54 inches in height and has a maximum weight capacity of 350 lbs.

2. Safety Information

• Always supervise children and individuals with limited mobility when using the pool steps.
• Do not dive or jump from the steps.
• Ensure the steps are properly weighted and secured to the pool deck before use to prevent floating or tipping.
• The handrails are for balance assistance only and are not designed to support full body weight. Avoid excessive pulling or hanging on the handrails.
• Regularly inspect the steps for any signs of wear, damage, or loose components. Do not use if damaged.
• Maximum weight capacity for these steps is 350 lbs. Do not exceed this limit.
• The closed side panels are designed to prevent entrapment behind the steps. Ensure they remain intact.

3. Package Contents

Verify that all components are present before beginning assembly:

• Step sections (multiple pieces)
• Handrails
• Mounting brackets for deck attachment
• Assembly hardware (screws, caps, etc.)
• Instruction manual

Note: Weights for securing the steps in the pool are sold separately and are highly recommended for stability.

4. Setup and Installation

Assembly of the Aqua Select Anti-Slip In-Pool Steps is designed to be straightforward with snap-together pieces. Follow these general steps for installation:

1. Assemble Step Sections: Connect the individual step sections according to the diagrams provided in the included printed instructions. Ensure all connections are secure.
2. Attach Handrails: Securely attach the handrails to the assembled step sections using the provided hardware.
3. Position Steps in Pool: Carefully place the assembled steps into your above-ground pool. Ensure the bottom of the steps rests firmly on the pool floor.
4. Weight the Steps: The steps will float without proper weighting. It is crucial to add sufficient weight to the bottom of the steps to keep them submerged and stable. This can be achieved using sand-filled weights or other suitable ballast (sold separately).
5. Mount to Deck: Adjust the deck attachment brackets to fit your pool deck, ensuring the deck height is between 48 and 54 inches. Securely fasten the brackets to the deck using appropriate hardware. Verify that the steps are stable and do not wobble.

Figure 1: Front view of the Aqua Select Anti-Slip In-Pool Steps.

Figure 2: Detail of the textured, anti-slip surface on each step for enhanced safety.

Figure 3: Adjustable brackets allow for secure mounting to pool decks.

Figure 4: Key dimensions: 10.5 inches deep steps and 24 inches clearance between handrails.

Figure 5: The steps installed in an above-ground pool, ready for use.

5. Operating Instructions

To use your Aqua Select Anti-Slip In-Pool Steps:

• Approach the steps facing the pool.
• Use the handrails for support and balance as you descend into the pool, stepping carefully on each textured tread.
• When exiting the pool, face the steps, use the handrails for support, and ascend carefully.
• Ensure the area around the steps on the deck is clear of obstructions.

6. Maintenance

Proper maintenance will extend the life of your pool steps:

• Cleaning: Regularly clean the steps with a mild soap solution and a soft brush to remove algae, dirt, and debris. Rinse thoroughly with fresh water. Avoid abrasive cleaners or harsh chemicals that could damage the plastic.
• Inspection: Periodically check all connections, screws, and mounting points for tightness and wear. Tighten any loose fasteners.
• Winterization: Before winter, remove the steps from the pool, clean them thoroughly, and store them in a dry, protected area away from direct sunlight and extreme temperatures.
• Water Flow: Ensure the slats in the back of the steps remain clear to allow for proper water circulation and prevent debris accumulation.

7. Troubleshooting

• Steps Float: This is a common issue if the steps are not adequately weighted. Ensure you have added sufficient ballast (e.g., sand-filled weights) to the bottom of the steps to keep them submerged.
• Steps Wobble: Check that the deck attachment brackets are securely fastened to the pool deck and that all assembly hardware is tightened. Ensure the steps are resting evenly on the pool floor.
• Algae Growth: Regular cleaning with a pool-safe cleaner and maintaining proper pool chemistry will help prevent algae growth on the steps. The slats are designed to help, but routine cleaning is still necessary.

8. Specifications

9. Warranty Information

Warranty coverage for Aqua Select products is typically provided by the retailer or seller at the point of purchase. Please refer to your purchase documentation or contact the seller directly for specific warranty terms and conditions. All parts manufactured for, or purchased from, Save More on Pool Supplies are warranted by Save More on Pool Supplies.

10. Support

For further assistance, questions, or to report any issues with your Aqua Select Anti-Slip In-Pool Steps, please contact the retailer or the Aqua Select customer support team. Refer to the contact information provided with your purchase or visit the official Aqua Select website for support resources.