Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Faber HOOD APEX FLHC SC BK 90 angular kitchen chimney. Please read this manual thoroughly before using the appliance to ensure safe and efficient operation. Keep this manual for future reference.
Image: Front view of the Faber HOOD APEX FLHC SC BK 90 kitchen chimney, showcasing its angular design and black finish.
Safety Information
Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and injury.
- Ensure the power supply matches the voltage specified on the appliance rating label.
- Do not allow children to operate or play with the chimney.
- Regularly clean the chimney to prevent grease buildup, which can be a fire hazard.
- Do not flambé under the range hood.
- Ensure adequate ventilation in the room when the chimney is used simultaneously with gas or other fuel-burning appliances.
- Disconnect the appliance from the power supply before cleaning or maintenance.
- Installation must be performed by a qualified technician.
Product Features
The Faber HOOD APEX FLHC SC BK 90 chimney is designed with advanced features for efficient kitchen ventilation.
- Type: Angular, Wall mounted, Auto-Clean chamber.
- Material: Black finish with front glass.
- Size: 90 cm, suitable for 3-5 burner stoves.
- Suction Capacity: 1500 m³/hr, ideal for kitchens over 200 sqft and heavy frying/grilling.
- Control Type: Touch and Gesture control for ease of use.
- Filter: Filterless Technology for improved suction and reduced maintenance.
- Lighting: LED 2 x 1.5 watt lamps for illuminating the cooking area.
- Noise Level: Maximum 58 dB.
- Special Features: Auto Clean function.
Image: Close-up of the touch control panel on the Faber HOOD APEX FLHC SC BK 90 chimney, showing power, speed, light, and auto-clean buttons.
Installation Guide (Setup)
Proper installation is crucial for the performance and safety of your chimney. It is highly recommended to have the chimney installed by a qualified Faber service technician.
- Unpacking: Carefully remove the chimney and all components from the packaging. Verify that all included components (1 chimney, 1 User Manual) are present and undamaged.
- Wall Preparation: Identify the mounting location on the wall, ensuring it is sturdy enough to support the chimney's weight (approximately 14 kg). Mark drilling points according to the provided template (if applicable). Ensure sufficient clearance above the cooking surface (typically 65-75 cm).
- Ducting: Install the exhaust ducting system. The chimney is designed for ducted ventilation. Ensure the ducting is straight and has minimal bends for optimal airflow.
- Mounting: Securely mount the chimney to the wall using appropriate fasteners. Ensure it is level and stable.
- Electrical Connection: Connect the chimney to a suitable 220 Volt power supply. Ensure the connection is properly grounded.
- Testing: After installation, power on the chimney and test all functions (suction speeds, lights, auto-clean) to ensure proper operation.
Image: Side view of the Faber HOOD APEX FLHC SC BK 90 chimney, illustrating its angular profile and wall-mounted design.
Operation
The Faber HOOD APEX FLHC SC BK 90 features intuitive touch and gesture controls.
- Power On/Off: Touch the ON/OFF icon to switch the chimney on or off.
- Speed Control: Use the numbered touch buttons (1, 2, 3) to select the desired suction speed. Speed 1 is for light cooking, while Speed 3 provides maximum suction for heavy cooking.
- Light Control: Touch the Light icon to turn the LED lamps on or off.
- Auto-Clean Function: Activate the Auto-Clean function by touching its dedicated icon. This feature helps to clean the internal components by heating and melting accumulated grease, which then collects in an oil collector. Refer to the cleaning section for details on emptying the oil collector.
- Gesture Control: This model supports gesture control for basic functions like power and speed adjustment. Wave your hand in front of the sensor to activate or change settings. Consult the full manual for specific gesture commands.
Image: Detailed view of the touch control interface, highlighting the icons for power, speed settings, light, and auto-clean functions.
Cleaning and Maintenance
Regular cleaning and maintenance ensure optimal performance and longevity of your chimney.
Filterless Cleaning
The filterless technology minimizes manual cleaning of filters. The auto-clean function helps in internal cleaning.
- Auto-Clean Cycle: Run the auto-clean cycle regularly (e.g., once every 15-30 days depending on usage). This process heats the internal chamber, causing grease to liquefy and drain into the oil collector.
- Emptying Oil Collector: The oil collector, usually located at the bottom or rear of the chimney, needs to be emptied periodically. Carefully remove the collector, dispose of the accumulated oil, and clean the collector with warm soapy water. Ensure it is dry before reinserting.
External Cleaning
- Wipe the exterior surfaces (black finish and glass) with a soft cloth dampened with mild detergent.
- Do not use abrasive cleaners, scouring pads, or harsh chemicals, as these can damage the finish.
- Ensure no water enters the electrical components.
Troubleshooting
Refer to this section for common issues and their potential solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Chimney does not turn on. | No power supply; loose connection; faulty switch. | Check power cord and circuit breaker. Ensure proper connection. Contact service if switch is faulty. |
| Low suction power. | Blocked ducting; oil collector full; motor issue. | Check ducting for obstructions. Empty and clean the oil collector. Contact service if motor performance is low. |
| Excessive noise during operation. | Loose parts; motor imbalance; ducting obstruction. | Ensure all parts are securely fastened. Check ducting for blockages. Contact service for motor inspection. |
| Lights not working. | Faulty LED lamp; loose connection. | Check connections. Contact service for lamp replacement. |
If the problem persists after attempting these solutions, please contact Faber customer support.
Specifications
| Feature | Detail |
|---|---|
| Model | HOOD APEX FLHC SC BK 90 |
| Type | Angular, Wall Mounted, Auto-Clean |
| Material | Glass (Black finish with front glass) |
| Size | 90 cm |
| Suction Capacity | 1500 m³/hr (1500 CMPH) |
| Control Type | Touch and Gesture |
| Filter Type | Filterless |
| Noise Level | 58 Decibels (Max) |
| Light Source Type | LED (2 x 1.5 watt) |
| Voltage | 220 Volts |
| Item Weight | 14 kg (14000 Grams) |
| Item Dimensions (LxWxH) | 37 x 90 x 90 Centimeters |
| Annual Energy Consumption | 180 Kilowatt Hours |
| Included Components | 1 chimney, 1 User Manual |
Warranty and Support
Your Faber HOOD APEX FLHC SC BK 90 chimney comes with a comprehensive warranty and dedicated customer support.
- Product Warranty: 1 year on the product.
- Motor Warranty: 5 years on the motor.
- Manufacturer: Marketed by Franke Faber India Pvt Ltd.
- Address: 1086/1/2, SANASWADI, TAL - SHIRUR, PUNE - 412208, MAHARASHTRA, INDIA.
- Customer Support Contact: 1800-209-3484.
For warranty claims, technical assistance, or service requests, please contact the customer support number provided. Ensure you have your purchase details and model number readily available.