Refresh R-9490Plus
Refresh R-9490Plus Refrigerator Water Filter Instruction Manual
Model: R-9490Plus
Brand: Refresh
Product Overview
The Refresh R-9490Plus Refrigerator Water Filter is designed to provide clean, great-tasting water directly from your refrigerator. This premium filter is certified to NSF/ANSI 53 and 42 standards, ensuring effective reduction of various contaminants while retaining beneficial minerals.
It is engineered for consistent flow rate and long-lasting performance, offering a reliable solution for your household's water filtration needs.
Compatibility
The Refresh R-9490Plus water filter is compatible with a range of LG and Kenmore refrigerator models. Please verify your refrigerator's existing filter or model number to ensure compatibility.
Compatible Filter Models:
- LG LT800P
- LG ADQ73613401
- Kenmore Elite 46-9490
- Kenmore 9490
- Kenmore 469490
- Kenmore ADQ73613402
Compatible Refrigerator Models (Partial List):
- LG LSXS26366D, LMXC23746S, LNXS30866D, LNXC23726S, LMXS30776D, LMXC23746D, LSXS26386D
- Kenmore 51863, 51833, 51832, 72483, 51823
- And many other LG and Kenmore models listed in product specifications.
Setup and Installation
Follow these steps to properly install your Refresh R-9490Plus water filter:
- Locate the Filter Compartment: Refer to your refrigerator's manual to find the water filter compartment. This is typically located in the upper right corner of the fresh food compartment or in the base grille.
- Remove the Old Filter: Twist the old filter counter-clockwise until it unlocks and can be pulled straight out. A small amount of water may drip out; this is normal.
- Prepare the New Filter: Remove the protective cap from the new Refresh filter.
- Insert the New Filter: Align the new filter with the filter housing. Push the filter firmly into the housing and twist it clockwise until it locks into place. You may feel a slight resistance as the filter seals.
- Flush the System: After installation, dispense approximately 2-3 gallons of water through the refrigerator's dispenser. This flushes out air and any carbon fines from the new filter, ensuring optimal performance and taste.
- Reset Filter Indicator: If your refrigerator has a filter change indicator light, reset it according to your refrigerator's instructions. This usually involves pressing and holding a specific button (e.g., 'Filter Reset' or 'Water Filter') for a few seconds.
Operating Instructions
Once installed, the Refresh R-9490Plus filter operates automatically, providing filtered water and ice. For best results:
- Initial Flushing: As mentioned in the setup, ensure you flush 2-3 gallons of water through the dispenser immediately after installation. This removes any trapped air and ensures the filter is fully primed.
- Regular Use: Use your refrigerator's water and ice dispenser as normal. The filter will continuously purify the water as it passes through.
- Water Quality: You should notice an improvement in the taste and odor of your water and ice.
Maintenance
Regular filter replacement is crucial for maintaining water quality and refrigerator performance.
Filter Replacement Schedule:
It is recommended to replace your Refresh R-9490Plus water filter every 6 months, or sooner if you notice a decrease in water flow or a change in water taste/odor. Filter life can vary based on water quality and usage volume.
Replacement Procedure:
Follow the same steps as outlined in the "Setup and Installation" section to replace the old filter with a new one. Always remember to flush the system after installing a new filter.
Troubleshooting
If you encounter any issues with your Refresh water filter, consider the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Slow Water Flow | Clogged filter, air in system, low water pressure. | Flush the filter for 2-3 gallons. If flow remains slow, replace the filter. Check household water pressure. |
| Bad Taste or Odor | New filter not flushed, filter expired, high contaminant levels. | Flush the filter thoroughly. If taste persists, replace the filter. Ensure filter is installed correctly. |
| Water Leaks from Filter Area | Improper installation, damaged O-rings. | Ensure filter is fully seated and twisted clockwise until locked. Remove and re-install the filter. Check O-rings for damage. |
| Filter Indicator Light Remains On | Indicator not reset. | Refer to your refrigerator's manual for specific instructions on how to reset the filter indicator light. |
Specifications
| Attribute | Detail |
|---|---|
| Model Number | R-9490Plus |
| Material | Premium Plus |
| External Testing Certification | IAPMO, ANSI, NSF (NSF/ANSI 53 & 42) |
| Product Benefits | Reduces chlorine, odor, heavy metals, particulates, cysts, and volatile organic compounds. |
| Unit Count | 2.0 Count (as per product listing) |
| Package Dimensions | 7.76 x 4.09 x 2.01 inches |
| Item Weight | 14.7 ounces |
| Manufacturer | Refresh |
| UPC | 859808007243 |
Warranty and Support
Refresh stands behind the quality of its products.
60-Day Satisfaction Promise:
Refresh offers a 60-day satisfaction promise on its products. If you have any questions regarding compatibility or product performance, please contact Refresh customer support.
For further assistance or inquiries, please refer to the contact information provided on the product packaging or the official Refresh website.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.