1. Product Overview
The Aramox DC 12V Universal Motorcycle Electronic Tachometer is designed to provide accurate engine RPM readings for most 12V motorcycles. Constructed from durable aluminum, it features a shockproof and corrosion-resistant housing. An internal light ensures clear data readability in various conditions.
- Measurement Range: 0-16000 rpm/min
- Voltage: DC 12V
- Outer Diameter: 65mm (2.6 inches)
- Inner Diameter: 58mm (2.3 inches)
- Material: Aluminum

Figure 1: Front view of the Aramox Electronic Tachometer.
2. Installation Instructions
This tachometer is designed for universal fitment on most DC 12V motorcycles. Professional installation is recommended. Ensure the motorcycle's power is off before beginning installation.
2.1 Wiring Diagram
The tachometer features multiple wires for connection. Proper wiring is essential for correct operation and to prevent damage to the unit or motorcycle electrical system. Refer to the following connections:
- Red Wire (Backlight Power): Connect to a switched 12V positive power source (e.g., ignition switch).
- Black Wire (Backlight Ground): Connect to a reliable ground point on the motorcycle chassis.
- Green Wire (Tachometer Signal): Connect to the negative side of the ignition coil. This is the signal wire for RPM measurement.
- Yellow with Black Line Wire (Tachometer Power): Connect to a switched 12V positive power source (e.g., ignition switch).
- Black Wire (Tachometer Ground): Connect to a reliable ground point on the motorcycle chassis.
Note: Some installations may combine the backlight and tachometer power/ground wires if appropriate for your motorcycle's electrical system. Ensure all connections are secure and insulated.

Figure 2: Tachometer showing wiring connections.

Figure 3: Detailed view of wire connectors.
2.2 Mounting
The tachometer includes a mounting bracket. Securely attach the tachometer to a suitable location on your motorcycle, such as the handlebars, ensuring it does not obstruct your view or interfere with controls. Use appropriate hardware to prevent vibration and ensure stability.

Figure 4: Rear view of the tachometer with mounting bracket.
3. Operating Instructions
Once properly installed and wired, the tachometer will display the engine's revolutions per minute (RPM) when the motorcycle is running. The internal LED light illuminates the display for visibility in low-light conditions.
- Turn the motorcycle ignition key to the "ON" position. The tachometer backlight should illuminate.
- Start the motorcycle engine. The tachometer needle will move to indicate the current engine RPM.
- Monitor the RPM during operation to ensure the engine is running within its optimal range.
4. Maintenance
The Aramox tachometer requires minimal maintenance. Follow these guidelines to ensure longevity:
- Keep the tachometer clean by wiping it with a soft, damp cloth. Avoid abrasive cleaners or solvents.
- Regularly check all wiring connections to ensure they remain secure and free from corrosion.
- Inspect the mounting bracket for tightness to prevent vibration-induced damage.
- Protect the unit from extreme weather conditions when possible.
5. Troubleshooting
If you encounter issues with your tachometer, refer to the following troubleshooting steps:
- Tachometer Not Functioning / No Display:
- Verify all wiring connections (power, ground, signal) are correct and secure.
- Check for blown fuses in the motorcycle's electrical system.
- Ensure the motorcycle's battery has sufficient charge (12V).
- Inaccurate or Lagging RPM Reading:
- Confirm the signal wire (Green) is correctly connected to the negative side of the ignition coil. An incorrect signal source can cause erratic readings.
- Ensure the connection to the ignition coil is clean and free of corrosion.
- Some motorcycles may require a signal filter if the ignition signal is noisy.
- Backlight Not Working:
- Check the Red (power) and Black (ground) wires for the backlight.
- Ensure the motorcycle's ignition is on.
If issues persist after following these steps, consult a qualified motorcycle technician.
6. Specifications
| Feature | Specification |
|---|---|
| Model Number | Aramox0kew2umhi9 |
| Measurement Range | 0-16000 rpm/min |
| Operating Voltage | DC 12V |
| Outer Diameter | 65mm (2.6 inches) |
| Inner Diameter | 58mm (2.3 inches) |
| Housing Material | Aluminum |
| Item Weight | 10 g (0.01 Kilograms) |
| Product Dimensions (L x W x H) | 10 x 10 x 10 cm (approximate) |
| Fitment | Universal for most DC 12V motorcycles |
7. Warranty and Support
7.1 Warranty Information
This Aramox product is covered by a 12-month warranty from the date of purchase. This warranty covers manufacturing defects and material faults under normal use. It does not cover damage caused by improper installation, misuse, accidents, or unauthorized modifications.
7.2 Customer Support
For technical assistance, warranty claims, or any questions regarding your Aramox tachometer, please contact Aramox customer service. Refer to your purchase documentation or the retailer's website for specific contact details.