1. Introduction
This manual provides essential information for the safe and efficient operation of your Intex Above Ground Underwater LED Magnetic Pool Light. Please read all instructions carefully before installation and use.
2. Safety Information
Always follow basic safety precautions when installing and using this electrical product. Failure to do so may result in serious injury or property damage.
- Ensure the power source is disconnected before any installation or maintenance.
- Do not attempt to open or repair the sealed light unit or external transmitter.
- Keep the external power unit and transformer away from water and out of reach of children.
- This product is designed for above-ground pools up to 24 feet in size.
3. Package Contents
Verify that all components are present:
- Light Unit (internal, waterproof)
- Transmitter (external, with power cord)
- Power Cord (for transmitter)
- Instruction Manual
Figure 1: Intex Magnetic Pool Lights (4 Pack) showing various color options.
4. Setup and Installation
The Intex Magnetic Pool Light uses magnetic induction to safely power the light unit through the pool wall. No wiring is required inside the pool.
4.1 Component Overview
Figure 2: Internal Light Unit (placed inside the pool).
Figure 3: External Transmitter Unit (placed outside the pool).
4.2 Installation Steps
- Separate the internal light unit from the external transmitter unit. They are held together magnetically.
- Place the internal light unit inside the pool, against the pool wall, at your desired location.
- Align the external transmitter unit on the outside of the pool wall, directly opposite the internal light unit. The strong magnets will hold them securely in place.
- Ensure the power cord from the external transmitter is routed safely away from the pool and connected to a suitable 110V AC outlet.
Figure 4: Magnetic light unit securely attached to the pool wall.
Important: If the internal light unit becomes separated from the external transmitter, it is designed to float to the surface for easy retrieval. The external power source is safe for use near water.
5. Operating Instructions
The light unit features multiple color modes for enhanced ambiance.
5.1 Powering On/Off and Changing Modes
Figure 5: Control buttons on the external transmitter unit.
- Plug the external transmitter's power cord into a 110V AC outlet.
- Press the power button on the external transmitter to turn the light on.
- Press the mode button repeatedly to cycle through the available color options: white, green, blue, and a color-changing mode.
- Press the power button again to turn the light off.
Video 1: Demonstration of the automatic color changing mode of the LED pool light.
5.2 Nighttime Illumination
The powerful LED light effectively illuminates pools up to 24 feet, providing clear visibility and a vibrant atmosphere for evening swims.
Figure 6: Pool illuminated by the Intex LED Magnetic Pool Light at night.
6. Maintenance
Regular maintenance ensures optimal performance and longevity of your pool light.
- Cleaning: Periodically wipe down the external transmitter unit with a damp cloth. The internal light unit can be cleaned with a soft brush or cloth while submerged.
- Storage: During off-season or extended periods of non-use, disconnect the power, remove both units from the pool wall, clean them thoroughly, and store them in a dry, cool place away from direct sunlight.
- Inspection: Regularly inspect the power cord for any signs of damage. If damaged, discontinue use and replace the unit.
7. Troubleshooting
If your Intex Magnetic Pool Light is not functioning as expected, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the transmitter. | Check if the power cord is securely plugged into a working outlet. |
| Light is dim or flickers. | Poor magnetic connection. | Ensure the internal light unit and external transmitter are perfectly aligned on opposite sides of the pool wall. |
| Light unit floats away. | Loss of magnetic connection. | This is a safety feature. Re-attach the external transmitter to the pool wall, aligning it with the internal unit. |
| Cannot change light colors. | Mode button not pressed correctly. | Press the mode button firmly and release. Ensure the unit is powered on. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Intex |
| Model Number | 28697E |
| Power Source | Corded Electric |
| Voltage | 110 Volts (AC) |
| Light Source Type | LED |
| Light Color | Multi-Color |
| Brightness | 800 Lumens |
| Installation Type | Wall Mount (Magnetic) |
| Control Method | Touch (on external unit) |
| Water Resistance Level | Water Resistant (internal unit) |
| Maximum Pool Size | Up to 24-foot pools |
9. Warranty and Support
For warranty information, product registration, or technical support, please refer to the official Intex website or contact Intex customer service directly. Keep your purchase receipt for warranty claims.