ESC 3 Way Touch Sensor Dimmer (150W) - Installation and Operation Manual

1. Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of your ESC 3 Way Touch Sensor Dimmer. This module is designed to replace or upgrade the touch control functionality in lamps, offering three levels of brightness (Low, Medium, High) and an Off state. It is compatible with both incandescent and LED bulbs up to 150 watts.

2. Safety Information

• Always disconnect power to the lamp before attempting any installation or repair.
• Ensure all wiring connections are secure and properly insulated.
• If you are unsure about any step, consult a qualified electrician.
• Do not exceed the maximum wattage rating of 150W.
• This device is for indoor use only and is not water resistant.

3. Package Contents

Your package should contain the following items:

• 1 x ESC 3 Way Touch Sensor Dimmer Module (Model MKTBA)
• 4 x Wire Nuts

4. Specifications

5. Setup & Installation

Before beginning installation, ensure the lamp is unplugged from the power outlet to prevent electrical shock. This touch sensor is designed for easy replacement of existing touch modules or integration into new lamp designs.

Figure 1: ESC 3 Way Touch Sensor Dimmer Module and Wire Nuts

This image shows the compact black touch sensor module with its four colored wires (red, black, white, green with a yellow ring terminal) and four orange wire nuts, which are used for making electrical connections.

5.1. Preparation

• Disconnect the lamp from the power source.
• Access the existing wiring within the lamp base.
• If replacing an old sensor, carefully cut the wires connected to the old module. Strip approximately 1/2 inch of insulation from the ends of the lamp wires and power cord wires to expose the raw copper. If existing wire nuts are removable, twist counter-clockwise to detach.

5.2. Wiring Instructions

Refer to the wiring diagram below for visual guidance. Use the provided wire nuts to make secure connections. Twist new orange wire nuts clockwise for new connections.

Figure 2: Simple and Easy Wiring Diagram for Installation

This image displays a clear wiring diagram. The touch sensor module has four wires: Green (Touch), White (Common), Red (Lamp), and Black (Power). The diagram illustrates how to connect these to the lamp's power plug (Neutral 'N', Hot 'H') and the lamp's bulb socket. Two options are shown for connecting the Green touch wire: Option 1 involves attaching the metal ring to the lamp base, and Option 2 involves wire-nutting it to an existing touch wire.

1. Green Wire (Touch): This wire connects to the metallic touch surface of your lamp.
   • Option 1: Attach the yellow metal ring terminal of the green wire to the lamp's metal base, typically by securing it under a bolt or screw that makes contact with the lamp's conductive surface.
   • Option 2: If your lamp has an existing touch wire, cut and strip it, then use a wire nut to connect it to the green wire from the sensor box.
2. White Wire (Common/Neutral): Use a wire nut to connect the WHITE wire from the sensor box to one of the wires from the lamp and one of the wires from the power plug. This creates a 3-wire connection (1 lamp wire, 1 plug wire, and 1 white sensor wire).
3. Red Wire (Lamp Hot): Use a wire nut to connect the RED wire from the sensor box to the only remaining wire from the lamp.
4. Black Wire (Power Hot): Use a wire nut to connect the BLACK wire from the sensor box to the only remaining wire from the power plug.

After all connections are made, ensure they are secure and insulated. Carefully tuck the wires and the sensor module back into the lamp base, ensuring no wires are pinched.

6. Operating Instructions

Once installed, the ESC 3 Way Touch Sensor Dimmer provides convenient control over your lamp's brightness. Simply touch any metallic part of the lamp to cycle through the brightness settings.

Figure 3: Universal 3 Way Touch Dimmer Compatibility

This image highlights the universal compatibility of the touch dimmer with three-way light bulbs, one-way light bulbs, LED, and incandescent bulbs. It also shows the LO-MED-HI-OFF sequence and that the module tucks easily under the lamp base.

6.1. Brightness Control Sequence

Each touch on the lamp's metallic surface will advance the light through the following sequence:

1. First Touch: Low Brightness
2. Second Touch: Medium Brightness
3. Third Touch: High Brightness
4. Fourth Touch: Off

The cycle repeats with subsequent touches.

Figure 4: Brightness Level Sequence

This illustration visually represents the four states of the touch dimmer: Low, Medium, High, and Off, demonstrating the sequential change in light intensity with each touch.

7. Maintenance

• Keep the lamp and sensor module clean and free from dust. Use a dry, soft cloth for cleaning.
• Ensure the lamp's metallic touch surface remains clean and free of obstructions for optimal performance.
• Regularly check wiring for any signs of wear or damage.

8. Troubleshooting

9. Warranty & Support

ESC provides a 30-day money-back guarantee for this product. If you encounter any issues with installation or performance within 30 days of purchase, please contact ESC customer support for assistance or a replacement.

For further support, please refer to the contact information provided with your purchase or visit the official ESC website.

10. Disposal Information

Please dispose of this product responsibly in accordance with local regulations for electronic waste. Do not dispose of electrical appliances as unsorted municipal waste. Use separate collection facilities.