Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Memphis Audio SRXP62C SRX Pro 6.5 Inch Component Speaker System. Please read this manual thoroughly before attempting installation or operation to ensure proper function and longevity of your product.
The SRXP62C system is designed to deliver high-quality audio performance in a vehicle environment, featuring separate mid-bass drivers, tweeters, and passive crossovers for optimized sound reproduction.
Safety Information
WARNING: Proposition 65 Warning
This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.
- Always disconnect the vehicle's battery before beginning any electrical installation.
- Ensure all wiring is properly insulated and secured to prevent short circuits and damage.
- Do not operate the audio system at excessively high volumes for prolonged periods, as this may cause hearing damage.
- Consult a professional installer if you are unsure about any part of the installation process.
Package Contents
Verify that all components are present in your package:
- 2 x SRXP62 Mid-Bass Drivers (6.5 inch woofers)
- 2 x SRPT Tweeters
- 2 x Passive Crossovers
- Mounting Hardware (screws, clips, etc. - may vary)
Figure 1: The complete Memphis Audio SRXP62C SRX Pro 6.5" Component Speaker System, including two mid-bass drivers, two tweeters, and two passive crossovers.
Setup and Installation
Proper installation is crucial for optimal performance. Follow these guidelines carefully.
1. Mid-Bass Driver Installation
- Select a suitable mounting location in your vehicle, typically door panels or kick panels, ensuring adequate depth and clearance.
- Cut the mounting hole to the specified diameter (6.5 inches).
- Connect the speaker wires from the passive crossover's 'WOOFER' output to the terminals on the mid-bass driver. Ensure correct polarity (+ to + and - to -).
- Secure the mid-bass driver using the provided mounting screws.
Figure 2: Front view of the Memphis Audio SRXP62C 6.5 inch mid-bass driver.
Figure 3: Angled front view of the Memphis Audio SRXP62C 6.5 inch mid-bass driver, showcasing the cone and surround.
2. Tweeter Installation
- Choose a mounting location for the tweeters that allows for optimal sound staging, typically higher up in the vehicle's interior (e.g., A-pillars, dash).
- Depending on the tweeter's design, you may need to flush mount or surface mount. Follow the specific instructions provided with the tweeter mounting hardware.
- Connect the tweeter wires from the passive crossover's 'TWEETER' output to the terminals on the tweeter. Observe correct polarity.
Figure 4: Front view of the Memphis Audio SRPT Tweeter, showing the protective grille.
Figure 5: Angled view of the Memphis Audio SRPT Tweeter, highlighting its design.
3. Passive Crossover Connection
- Mount the passive crossovers in a secure, dry location, away from excessive heat or moisture.
- Connect the audio signal from your amplifier's speaker output to the 'INPUT' terminals on the passive crossover.
- Connect the 'WOOFER' output terminals of the crossover to the mid-bass driver.
- Connect the 'TWEETER' output terminals of the crossover to the tweeter.
- Ensure all connections are tight and secure to prevent signal loss or intermittent operation.
Figure 6: Top view of the Memphis Audio passive crossover, showing clearly labeled input, woofer, and tweeter terminals.
Figure 7: Side view of the Memphis Audio passive crossover, illustrating the connection points.
Figure 8: Memphis Audio passive crossover with approximate dimensions (3.3"H x 11.7"W x 15"D) for installation planning.
Operating Instructions
Once installed, follow these steps for initial operation:
- Initial Power On: After verifying all connections, turn on your vehicle's audio system. Start with the volume at its lowest setting.
- Volume Adjustment: Gradually increase the volume to a comfortable listening level. Listen for any distortion or unusual noises.
- Audio Settings: Adjust your head unit's or amplifier's equalizer and balance/fader settings to achieve your preferred sound. Avoid excessive bass or treble boost, which can lead to distortion.
- Break-in Period: Allow a break-in period of several hours of normal listening for the speakers to reach their optimal performance.
Maintenance
To ensure the longevity and performance of your speaker system, follow these simple maintenance tips:
- Cleaning: Use a soft, dry cloth to gently wipe down the speaker grilles and surrounds. Avoid using harsh chemicals or abrasive cleaners.
- Inspection: Periodically check all wiring connections to ensure they remain secure. Inspect speaker cones and surrounds for any signs of damage or wear.
- Environmental Factors: Protect the speakers from direct exposure to extreme temperatures, moisture, and direct sunlight, which can degrade materials over time.
Troubleshooting
If you encounter issues with your speaker system, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound from speakers | Loose or incorrect wiring connections Amplifier not powered on or in protect mode Head unit settings (e.g., fader/balance) | Check all speaker and amplifier connections for proper polarity and tightness. Verify amplifier power and status indicators. Adjust head unit settings. |
| Distorted or unclear sound | Volume too high, causing clipping Incorrect amplifier gain settings Damaged speaker cone or surround | Reduce volume. Adjust amplifier gain settings appropriately. Inspect speakers for physical damage. |
| One speaker not working | Faulty wiring to that speaker Damaged speaker or crossover component | Check wiring for the affected speaker. Swap speakers or crossover components (if possible) to isolate the issue. |
Specifications
Key technical specifications for the Memphis Audio SRXP62C SRX Pro 6.5 Inch Component Speaker System:
- Model Name: SRXP62C
- Speaker Type: Component
- Speaker Size: 6.5 Inches (Woofer Diameter)
- Speaker Maximum Output Power: 250 Watts
- Impedance: 6.5 Ohm
- Connectivity Technology: Coaxial (referring to the system type, not wiring)
- Audio Output Mode: Stereo
- Surround Sound Channel Configuration: 2.0
- Audio Driver Type: Dynamic Driver
- Recommended Uses For Product: Cloth Treated (referring to surround material)
- Product Dimensions: 3.15"D x 11.77"W x 15.12"H (Package Dimensions)
- Item Weight: 1.38 pounds
- UPC: 702588209249
- Manufacturer: Memphis Audio
- Date First Available: April 2, 2019
Warranty Information
The Memphis Audio SRXP62C SRX Pro 6.5 Inch Component Speaker System comes with a Limited Warranty. Specific terms and conditions of the warranty, including duration and coverage details, are typically provided with your purchase documentation or can be obtained directly from Memphis Audio or your authorized dealer. Please retain your proof of purchase for warranty claims.
Support
For technical assistance, warranty claims, or further information regarding your Memphis Audio SRXP62C SRX Pro 6.5 Inch Component Speaker System, please contact Memphis Audio directly or visit their official website. You may also reach out to your authorized dealer for support.
Manufacturer: Memphis Audio
Website: Memphis Audio Store on Amazon (for general product information)