Introduction
The Eastwood 4 Tier Tree Mobile Masking Station is designed to organize and facilitate the dispensing of masking paper and film for various painting and bodywork applications. This portable system helps keep your materials clean and readily accessible, improving efficiency in your workspace.
Key features include:
- Holds two 18-inch and two 12-inch paper rolls.
- Designed for easy loading and dispensing of paper.
- Lightweight frame with a wide base for stability.
- Durable powder-coated finish.
- Integrated cutting blades for precise material separation.
- Two sturdy rear wheels for mobility.
Figure 1: The Eastwood 4 Tier Tree Mobile Masking Station, fully assembled and loaded with masking paper and tape.
Setup and Assembly
The Eastwood 4 Tier Tree Mobile Masking Station requires assembly. It is recommended to lay out all components before beginning assembly. Assembly typically takes approximately 45 minutes.
Components Checklist:
- Main frame sections
- Crossbars/Paper holders (4 sets)
- Cutting blade assemblies (4)
- Wheels (2)
- Handle
- All necessary fasteners (bolts, nuts, washers)
- Tape dispenser rods (4)
Assembly Steps:
- Unpack Components: Carefully remove all parts from the packaging. Verify that all components listed in the checklist are present. If any parts are missing or damaged, contact customer support.
- Assemble Base: Attach the main vertical frame sections to the base support structure. Ensure all connections are secure.
- Attach Wheels: Securely fasten the two wheels to the designated axle points on the base.
- Install Paper Holders: Mount the four paper holder crossbars onto the main frame. The station is designed to hold two 12-inch wide rolls on the upper tiers and two 18-inch wide rolls on the lower tiers. Ensure the correct orientation for each tier.
- Attach Cutting Blade Assemblies: Securely attach the cutting blade assemblies to the front of each paper holder. Exercise caution as these blades are sharp.
- Install Tape Dispenser Rods: Insert the tape dispenser rods into their respective slots, typically located near the top paper holders.
- Attach Handle: Secure the handle to the top of the main frame.
- Final Inspection: Once assembled, check all bolts and connections to ensure they are tightened properly for stability and safe operation.
Figure 2: Detail of a paper roll holder and the integrated cutting blade. Note the serrated edge for cutting.
Figure 3: View of the tape dispenser mechanism, showing how tape rolls are mounted.
Operating Instructions
Loading Masking Paper/Film:
- Ensure the masking station is stable and on a level surface.
- For each tier, slide the appropriate size paper or film roll onto the support rod.
- Feed the leading edge of the paper/film under the cutting blade assembly. Ensure it is straight and aligned.
- For the tape dispensers, slide the tape rolls onto the smaller rods provided.
Dispensing and Cutting:
- Grasp the leading edge of the masking paper/film.
- Pull the paper/film smoothly and evenly to the desired length. The wide base design helps prevent tipping during this process.
- Once the desired length is reached, press the paper/film firmly against the cutting blade and pull upwards or downwards to cleanly tear the material.
- For tape, pull the desired length and use the integrated tape cutter or a separate tool to cut.
Figure 4: A user demonstrating the process of pulling and cutting masking paper from the station.
Maintenance
- Cleaning: Regularly wipe down the frame and components with a damp cloth to remove dust, paint residue, or other debris. Avoid abrasive cleaners that could damage the powder-coated finish.
- Blade Inspection: Periodically inspect the cutting blades for any damage or dullness. Sharp cutting edges are crucial for clean cuts. Warning: The cutting edges are sharp. Handle with extreme care to avoid injury.
- Fastener Check: Over time, vibrations or movement may loosen fasteners. Periodically check all bolts and nuts and tighten them as necessary to maintain stability.
- Wheel Condition: Inspect the wheels for any damage or excessive wear. Ensure they rotate freely for easy mobility.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Station is unstable or wobbly. | Loose fasteners; uneven surface. | Check and tighten all bolts and nuts. Ensure the station is on a flat, level surface. |
| Difficulty dispensing paper/film. | Rolls not properly seated; obstruction; damaged roll. | Ensure rolls are correctly placed on the support rods and rotate freely. Check for any debris obstructing the path. |
| Paper/film tears unevenly or is difficult to cut. | Dull or damaged cutting blade; improper cutting technique. | Inspect the cutting blade for damage. Ensure you are applying even pressure across the blade when cutting. |
| Missing parts upon arrival. | Packaging error or transit damage. | Contact Eastwood customer support immediately with your purchase details and a list of missing parts. |
Specifications
- Product Dimensions: Approximately 42.5 x 11.1 x 5.5 inches (packaged)
- Product Weight: Approximately 23.35 Pounds (packaged)
- Material Capacity:
- Two (2) paper/film rolls up to 12 inches wide.
- Two (2) paper/film rolls up to 18 inches wide.
- Four (4) tape rolls (typically 3/4 inch wide).
- Construction: Double welded lightweight powder-coated frame
- Mobility: Two rear wheels
- Manufacturer: Eastwood
- Model Number: B07PVKP2B8
- Country of Origin: China
Warranty Information
The Eastwood 4 Tier Tree Mobile Masking Station comes with a 1-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, abuse, accidents, unauthorized repairs, or normal wear and tear.
For warranty claims, please retain your proof of purchase and contact Eastwood customer support.
Additionally, the product is eligible for a 90-day return policy from the point of purchase, subject to the retailer's terms and conditions.
Customer Support
For technical assistance, missing parts, or any questions regarding your Eastwood 4 Tier Tree Mobile Masking Station, please contact Eastwood customer support. Eastwood provides lifetime technical support for its products.
You can find more information and contact details by visiting the official Eastwood store:
Eastwood is committed to providing high-quality, innovative products and stands behind its solutions with a 100% Satisfaction Guarantee since 1978.
