1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your JVC KD-X560BT Digital Media Receiver. The KD-X560BT is a versatile car and marine stereo featuring a 3-inch color screen, Bluetooth connectivity, USB and AUX inputs, and a rear camera input. Its shallow chassis design and marine-rated construction make it suitable for various vehicle types, including cars, Jeeps, convertibles, and boats.
2. Safety Information
Please read all safety instructions carefully before installing or operating the unit. Failure to follow these instructions may result in injury or damage to the unit or vehicle.
- Electrical Safety: Ensure proper wiring and fuse protection to prevent electrical shorts or fire hazards. Disconnect the vehicle's negative battery terminal before installation.
- Installation: Install the unit securely to prevent it from detaching during sudden stops or impacts. Avoid installing in locations that obstruct the driver's view or interfere with vehicle operation.
- Operation: Do not operate the unit in a manner that distracts you from driving. Always keep your attention on the road. Adjust volume to a safe level to hear outside traffic sounds.
- Moisture Protection: While marine-rated, avoid direct exposure to high-pressure water sprays. Ensure all connections are properly sealed in marine environments.
3. Package Contents
Verify that all items are present in the package before beginning installation.
Image: JVC KD-X560BT package contents, showing the main unit, wiring harness, external microphone, mounting hardware, and documentation.
- JVC KD-X560BT Digital Media Receiver (Head Unit)
- Wiring Harness
- Mounting Hardware (screws, brackets)
- External Microphone
- Instruction Manuals (Quick Start Guide, Full Manual)
4. Setup
4.1. Installation
The KD-X560BT features a shallow chassis design, allowing for easier installation in a wider range of vehicles. Ensure adequate space and proper ventilation around the unit.
Image: JVC KD-X560BT installed in a vehicle's dashboard.
4.1.1. Wiring Connections
Refer to the wiring diagram provided with your unit for specific connections. Key connections include:
Image: Rear view of the KD-X560BT with wiring connections highlighted.
- Power and Ground: Connect the yellow wire to constant 12V, red wire to switched 12V (ignition), and black wire to a clean chassis ground.
- Speaker Outputs: Connect to your vehicle's speakers. Observe correct polarity.
- Preamp Outputs: Three sets of RCA preamp outputs are available for connecting external amplifiers and subwoofers.
- Rear Camera Input: Connect the video output of an optional rear-view camera to the dedicated input. The reverse gear signal wire should be connected to trigger the camera display automatically.
- Steering Wheel Remote Input: For connecting an optional steering wheel control interface (adapter may be required).
- Antenna: Connect your vehicle's antenna cable.
4.1.2. Marine Environment Considerations
The KD-X560BT features a conformal coating on its electronic circuits for enhanced moisture protection. When installing in a marine environment, ensure all connections are properly insulated and protected from water ingress to maximize the unit's lifespan.
4.2. Initial Power-On
After completing all wiring, reconnect the vehicle's negative battery terminal. Press the power button to turn on the unit. Follow any on-screen prompts for initial setup, such as language selection or clock adjustment.
5. Operating Instructions
Image: Front view of the KD-X560BT showing the display during Bluetooth audio playback.
5.1. Basic Controls
- Power Button: Press to turn the unit on/off.
- Rotary Knob: Turn to adjust volume. Press to access menu options or confirm selections.
- Source Button: Press to cycle through available audio sources (FM, AM, Bluetooth, USB, AUX).
- Menu Button: Access the main menu for settings and adjustments.
- Navigation Buttons: Use for track skipping, station tuning, and menu navigation.
5.2. Source Selection
Press the source button or navigate through the on-screen menu to select your desired audio input.
Image: KD-X560BT display showing the source selection screen.
5.3. Bluetooth Operation
- Pairing: Enable Bluetooth on your smartphone. On the KD-X560BT, select Bluetooth as the source and enter pairing mode. Select "KD-X560BT" from your phone's Bluetooth device list.
- Audio Streaming: Once paired, you can stream audio from your smartphone to the receiver. Use the unit's controls for play/pause and track skipping.
- Hands-Free Calling: When a call comes in, the unit will display caller information. Use the dedicated call buttons on the unit to answer or end calls. The included external microphone ensures clear communication.
5.4. USB Playback
Connect a USB storage device (e.g., USB flash drive) to the front USB port. The unit will automatically detect and begin playing compatible audio files (WMA, MP3, WAV, FLAC). Use the navigation buttons to browse folders and tracks.
5.5. AUX Input
Connect an external audio player to the front 3.5mm AUX input using a stereo mini-jack cable. Select AUX as the source to play audio from the connected device.
5.6. Radio Tuner
Select FM or AM as the source. Use the seek buttons to find radio stations. Press and hold a preset button to store the current station. Press briefly to recall a stored station.
5.7. Sound Settings
Access the sound menu to customize your audio experience:
- 13-Band Equalizer (EQ): Adjust frequency bands to fine-tune the audio output to your preference.
- Time Alignment: Adjust the delay for each speaker to ensure sound reaches the listener at the same time, creating a more focused soundstage.
- Bass Boost: Enhance low-frequency response.
- Loudness: Compensates for the ear's decreased sensitivity to low and high frequencies at low volume levels.
5.8. Rear Camera Function
The KD-X560BT supports an optional rear-view camera. When connected and properly wired, the unit's 3-inch screen will automatically display the camera feed when the vehicle is shifted into reverse. A dedicated "CAMERA" button on the front panel allows manual activation of the camera view at any time.
Image: KD-X560BT displaying a rear camera feed.
6. Maintenance
- Cleaning the Unit: Use a soft, dry cloth to wipe the front panel. For stubborn dirt, dampen the cloth with water. Avoid using abrasive cleaners or solvents.
- Screen Care: The 3-inch screen should be cleaned gently with a soft, lint-free cloth. Do not press hard on the screen.
- Connections: Periodically check all wiring connections to ensure they are secure, especially in marine environments where corrosion can occur.
7. Troubleshooting
If you encounter issues with your KD-X560BT, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Blown fuse, incorrect wiring, vehicle battery issue | Check vehicle fuses and the unit's fuse. Verify power and ground connections. Check vehicle battery. |
| No sound | Volume too low, mute activated, incorrect speaker wiring, amplifier issue (if external amp used) | Increase volume. Check if mute is active. Verify speaker connections. Check external amplifier status. |
| Bluetooth not connecting | Not in pairing mode, device already paired to another unit, Bluetooth off on phone | Ensure unit is in pairing mode. Delete previous pairings on phone and unit. Turn Bluetooth on/off on phone. |
| USB device not recognized | Incompatible file format, damaged USB device, unsupported capacity | Check file formats. Try a different USB device. Ensure device is formatted correctly (FAT32). |
| Rear camera not displaying | Camera not connected, reverse signal wire not connected, camera malfunction | Verify camera video and power connections. Ensure reverse signal wire is correctly connected. Test camera functionality. |
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | KD-X560BT |
| Display | 3-inch Color Screen |
| Connectivity | Bluetooth, USB, 3.5mm AUX |
| Audio Encoding Support | WMA, MP3, WAV, FLAC |
| Video Encoding Support | H.264, MPEG-4 (for camera input) |
| Equalizer | 13-Band EQ |
| Preamp Outputs | 3 sets (Front, Rear, Subwoofer) |
| Rear Camera Input | Yes |
| Chassis Depth | Under 5 inches (shallow chassis) |
| Product Dimensions | 4.49 x 9.25 x 9.37 inches (approximate) |
| Item Weight | 1 pound |
| First Available | March 30, 2019 |
9. Warranty and Support
JVC products are designed and manufactured to the highest quality standards. For warranty information, please refer to the warranty card included with your product or visit the official JVC website. For technical support or service inquiries, please contact JVC customer service or an authorized service center.
Keep your purchase receipt as proof of purchase for warranty claims.
