Important Safety Information
Read all instructions carefully before installation and use. Failure to follow these instructions may result in electric shock, fire, or other hazards that could cause injury or property damage.
- WARNING: Risk of electric shock. Disconnect power at the circuit breaker or fuse box before installation or servicing.
- All wiring connections must be in accordance with local and national electrical codes (NEC). Consult a qualified electrician if you are unsure about wiring procedures.
- This fixture is designed for outdoor use and is water resistant. Ensure all connections are properly sealed to prevent water intrusion.
- Do not install this fixture near flammable materials or in areas with explosive atmospheres.
- Proposition 65 Warning: This product may expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
Package Contents
Verify that all components are present before beginning installation:
- LED Light Fixture (Sconce)
- Mounting Backplate
- Frame
- Seeded Crystal Glass Element
- Hardware Pack (screws, wire nuts, etc.)
Image: The Elk Home Emode 87110/LED outdoor sconce, featuring a matte black finish and a clear seeded crystal glass element.
Installation Instructions
Tools Required (Not Included):
- Phillips head screwdriver
- Flathead screwdriver
- Wire strippers
- Electrical tape
- Safety glasses
Pre-Installation:
- Turn off electrical power at the main fuse box or circuit breaker.
- Carefully unpack the fixture and check for any damage.
- Ensure all parts listed in the 'Package Contents' section are present.
Mounting the Fixture:
- Attach the mounting backplate to the junction box using the provided screws. Ensure the backplate is securely fastened to the wall surface.
- Connect the fixture's ground wire (usually bare copper or green) to the house ground wire using a wire nut. If your junction box has a ground screw, wrap the fixture's ground wire around it.
- Connect the fixture's neutral wire (usually white) to the house neutral wire (white) using a wire nut.
- Connect the fixture's hot wire (usually black) to the house hot wire (black) using a wire nut.
- Carefully tuck all wires into the junction box.
- Align the fixture body with the mounting backplate and secure it with the provided screws.
- Install the seeded crystal glass element into the fixture frame according to the specific design.
Image: Side view of the Elk Home Emode outdoor sconce, illustrating its profile and the seeded crystal detail.
Operating Instructions
Once the fixture is securely installed and wired, restore power at the circuit breaker.
- The Elk Home Emode 87110/LED Sconce is designed to be controlled via a standard wall switch or a compatible remote control system (remote control not included unless specified separately).
- Flip the wall switch to the 'ON' position to illuminate the fixture.
- Flip the wall switch to the 'OFF' position to turn off the fixture.
- If using a remote control system, refer to the remote control's specific instructions for pairing and operation.
Image: A close-up view of the Elk Home Emode sconce with its integrated LED light illuminated, highlighting the seeded crystal effect.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your outdoor sconce.
- Cleaning: To clean the fixture, ensure power is turned off at the circuit breaker. Use a soft, dry, or slightly damp cloth. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish or crystal.
- LED Light Source: This fixture uses an integrated LED light source. There are no replaceable bulbs. If the LED light source fails, the entire fixture may need to be replaced.
- Inspection: Periodically inspect the fixture for any signs of wear, damage, or loose connections. Address any issues promptly.
Troubleshooting
If your Elk Home Emode outdoor sconce is not functioning correctly, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. | Check the circuit breaker or fuse. Ensure the wall switch is in the 'ON' position. |
| Light flickers or is dim. | Loose wiring connection. | Turn off power at the circuit breaker. Check all wire connections for tightness. |
| Fixture is damaged. | Physical damage during installation or use. | If the fixture is physically damaged, it may need to be replaced. Do not attempt to repair electrical components unless qualified. |
If the problem persists after attempting these solutions, consult a qualified electrician or contact customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | 87110/LED |
| Brand | Elk Home |
| Dimensions (L x W x H) | 2.5" x 4.75" x 14" |
| Item Weight | 4.25 Pounds |
| Color | Matte Black |
| Material | Aluminum, Glass (Seeded Crystal) |
| Light Source Type | Integrated LED |
| Wattage | 11 watts |
| Brightness | 460 Lumens |
| Color Temperature | 3000 Kelvin |
| CRI | 80 |
| Voltage | 120 Volts |
| Power Source | Hardwired |
| Installation Type | Semi Flush Mount |
| Indoor/Outdoor Usage | Outdoor |
| Water Resistance Level | Water Resistant |
| Certifications | UL Listed |
Image: A diagram illustrating the 14-inch (36 cm) height of the Elk Home Emode outdoor sconce.
Warranty and Support
This Elk Home Emode 87110/LED Outdoor Sconce is covered by a 1-year limited manufacturer's warranty from the date of purchase.
This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, accident, misuse, abuse, or unauthorized modifications.
For warranty claims or technical support, please contact Elk Home customer service. Keep your proof of purchase for warranty validation.
Customer Support: For assistance, please visit the official Elk Home website or refer to your purchase documentation for contact information.
