CISCO DESIGNED PWR-C5-600WAC Power Supply User Manual

1. Introduction

This manual provides essential instructions for the safe and efficient installation, operation, and maintenance of the CISCO DESIGNED PWR-C5-600WAC Power Supply. This power supply is specifically designed for use with Cisco Catalyst 9200L Series Switches, providing reliable 600 Watt AC power. Please read this manual thoroughly before proceeding with installation or operation.

2. Safety Information

Adherence to the following safety guidelines is crucial to prevent injury and damage to the equipment.

• Electrical Safety: Always disconnect the power source before installing, removing, or servicing the power supply. Ensure proper grounding of the switch and power supply.
• Handling: Handle the power supply with care. Avoid dropping or subjecting it to physical shock.
• Environment: Do not operate the power supply in wet or damp conditions. Ensure adequate ventilation around the switch to prevent overheating.
• Qualified Personnel: Installation and servicing should only be performed by qualified personnel familiar with network equipment and electrical safety procedures.

3. Product Overview

The CISCO DESIGNED PWR-C5-600WAC is a 600-watt AC power supply module designed for hot-swappable installation in compatible Cisco Catalyst 9200L Series Switches. It provides redundant or primary power to ensure continuous operation of your network infrastructure.

Figure 1: Three-quarter view of the CISCO DESIGNED PWR-C5-600WAC Power Supply, showing the main body and the AC power inlet.

Figure 2: Rear view of the CISCO DESIGNED PWR-C5-600WAC Power Supply, highlighting the AC power inlet and ventilation grille.

4. Specifications

Key technical specifications for the PWR-C5-600WAC Power Supply:

5. Setup and Installation

The PWR-C5-600WAC power supply is designed for hot-swappable installation, meaning it can be inserted or removed while the Cisco Catalyst 9200L Series Switch is operational, provided the switch has another active power source.

Installation Procedure:

1. Prepare the Slot: Identify an empty power supply slot on your Cisco Catalyst 9200L Series Switch. If replacing an existing power supply, ensure it is safely removed first.
2. Orient the Power Supply: Hold the PWR-C5-600WAC power supply with the AC inlet facing outwards and the handle towards you.
3. Insert the Module: Carefully slide the power supply into the designated slot until it is fully seated and the latch mechanism clicks into place. Ensure it is flush with the switch chassis.
4. Connect Power: Connect a suitable AC power cord to the power supply's AC inlet and then to a grounded AC power outlet.
5. Verify Operation: Observe the power supply's status indicator lights. A solid green light typically indicates normal operation. Refer to your switch's documentation for specific indicator meanings.

Removal Procedure:

1. Disconnect Power: Disconnect the AC power cord from the power supply.
2. Release Latch: Press the release latch or lever on the power supply module.
3. Remove Module: Gently pull the power supply module straight out of the chassis slot.

6. Operation

Once properly installed and connected to an AC power source, the PWR-C5-600WAC power supply operates automatically. It provides the necessary power to the Cisco Catalyst 9200L Series Switch. The primary operational feedback is provided by the status indicator lights on the power supply module itself and on the switch chassis.

• Normal Operation: A steady green indicator light on the power supply typically signifies that the unit is functioning correctly and supplying power.
• Redundancy: If two power supplies are installed, they operate in a redundant configuration, providing fault tolerance.

For detailed information on power supply status indicators and their meanings, consult the specific documentation for your Cisco Catalyst 9200L Series Switch model.

7. Maintenance

The PWR-C5-600WAC power supply is designed for minimal maintenance. However, periodic checks can help ensure its longevity and reliable performance.

• Ventilation: Ensure that the ventilation openings on the power supply and the switch chassis are clear of dust and debris. Blocked vents can lead to overheating.
• Cables: Periodically inspect the AC power cord for any signs of damage, fraying, or loose connections. Replace damaged cords immediately.
• Cleaning: If necessary, gently clean the exterior of the power supply with a soft, dry, lint-free cloth. Do not use liquid cleaners or solvents.
• Internal Components: There are no user-serviceable parts inside the power supply. Do not attempt to open or repair the unit. Refer all servicing to qualified Cisco service personnel.

8. Troubleshooting

If you encounter issues with your PWR-C5-600WAC power supply, consider the following troubleshooting steps:

• No Power/No Indicator Lights:
  • Verify that the AC power cord is securely connected to both the power supply and a functional AC power outlet.
  • Check the circuit breaker or fuse for the AC power outlet.
  • Ensure the power supply module is fully seated in its slot within the switch chassis.
• Abnormal Indicator Lights:
  • If the indicator light is amber, red, or blinking in an unexpected pattern, consult the Cisco Catalyst 9200L Series Switch documentation for specific error codes and their resolutions.
  • Attempt to reseat the power supply module.
• Switch Not Powering On (with power supply installed):
  • Ensure the switch's power button (if applicable) is in the 'on' position.
  • If multiple power supplies are installed, check the status of all units.
  • If possible, test with a known good power supply or in a different compatible switch slot.

If these steps do not resolve the issue, contact Cisco technical support or your authorized reseller for further assistance.

9. Warranty and Support

The CISCO DESIGNED PWR-C5-600WAC Power Supply is manufactured by CISCO SYSTEMS - ENTERPRISE and is covered by the standard manufacturer's warranty. The terms and duration of the warranty are subject to Cisco's official warranty policy, which can be found on their official website or obtained from your authorized Cisco reseller.

For warranty claims, technical support, or service inquiries, please contact your authorized Cisco reseller or visit the official Cisco support website. It is recommended to retain your proof of purchase for warranty validation.