MENABO Delta Roof Bar Fixing Kit

Introduction

This user manual provides essential information for the safe and correct installation, operation, and maintenance of your MENABO Delta Roof Bar Fixing Kit. This kit is designed to provide a secure base for roof bars on vehicles with normal roofs, enabling the transport of various cargo.

The kit is compatible with specific vehicle models, including DODGE Journey 5p 08>11, FIAT Freemont 5p 11>, HONDA CR-V IV 5p 12>, MAZDA 2 λ5p 07>09, 3 / Axela (BK) 5p 03>09, MINI Cooper 3p 14>, Cooper S 3p 14>, and One 3p 14>.

Safety Information

• Always read and understand all instructions before installation and use.
• Ensure all components are securely fastened before driving. Regularly check tightness during use.
• Do not exceed the maximum load capacity specified for your vehicle's roof or the roof bar system. Refer to your vehicle's owner's manual.
• Distribute cargo evenly on the roof bars.
• Adjust driving speed according to road conditions and cargo. Avoid sudden braking or sharp turns.
• Remove the roof bar system when not in use, especially for long periods or automatic car washes.
• Keep children away from the product during installation and removal.

Package Contents

Verify that all components listed below are present in your package. If any parts are missing or damaged, contact your retailer.

Figure 1: Overview of the MENABO Delta Roof Bar Fixing Kit components. The image displays the various parts required for assembly, including the rubber pads, base plates, vertical supports, metal clamps, and mounting hardware.

• 4 x Rubber Pads (for roof protection)
• 4 x Base Plates (main support for roof bars)
• 4 x Vertical Supports (connect base plate to roof bar)
• 4 x Metal Clamps (secure the kit to the vehicle's roof edge)
• 4 x Bolts with Washers (for assembly)
• Instruction Manual (this document)

Setup and Installation

Follow these steps carefully to install the MENABO Delta Roof Bar Fixing Kit on your vehicle. Ensure your vehicle is parked on a level surface and the engine is off.

1. Prepare the Roof: Clean the area of the vehicle's roof where the roof bars will be mounted. Ensure it is free of dirt, dust, and debris.
2. Attach Rubber Pads: Place the rubber pads onto the underside of the base plates. These pads protect your vehicle's paintwork.
3. Assemble Base Units: Connect the vertical supports to the base plates using the provided bolts and washers. Do not fully tighten yet.
4. Position Base Units: Carefully place the assembled base units onto the vehicle's roof, aligning them with the designated mounting points or door frames as per your vehicle's specifications. Ensure the rubber pads are correctly seated.
5. Attach Metal Clamps: Insert the metal clamps into the base units and hook them securely under the vehicle's door frame or designated roof edge.
6. Install Roof Bars: Mount your MENABO roof bars (sold separately) onto the vertical supports of the fixing kit. Ensure the bars are centered and evenly spaced.
7. Tighten All Fasteners: Systematically tighten all bolts and clamps. Start by hand-tightening, then use an appropriate tool to ensure a firm, secure fit. Do not overtighten.
8. Final Check: Gently pull on the installed roof bar system to confirm it is securely attached and does not move.

Figure 2: An example of a securely installed MENABO roof bar foot, demonstrating how the base plate and clamp integrate with the vehicle's roof edge.

Operating Instructions

Once installed, the MENABO Delta Roof Bar Fixing Kit provides a stable platform for your roof bars. Proper operation involves understanding load limits and driving considerations.

• Load Capacity: Always adhere to the maximum load capacity specified by your vehicle manufacturer and the roof bar manufacturer. Never exceed the lower of these two limits.
• Cargo Securing: Ensure all cargo placed on the roof bars is securely fastened using appropriate straps or tie-downs. Loose cargo can shift during transit, causing damage or accidents.
• Driving Adjustments: When carrying cargo on the roof, be aware of changes in your vehicle's center of gravity, wind resistance, and overall height. Drive at reduced speeds, especially in crosswinds, and allow for increased braking distances.
• Height Clearance: Be mindful of reduced overhead clearance when entering garages, carports, or low-clearance areas.

Maintenance

Regular maintenance ensures the longevity and safe operation of your roof bar fixing kit.

• Regular Inspection: Periodically inspect all components for signs of wear, damage, or corrosion. Check bolts and clamps for tightness, especially after the first few uses and before long journeys.
• Cleaning: Clean the components with mild soap and water. Avoid harsh chemicals or abrasive cleaners that could damage the finish or rubber parts.
• Storage: If removing the kit for extended periods, store it in a clean, dry place away from direct sunlight and extreme temperatures.

Troubleshooting

This section addresses common issues you might encounter.

Specifications

• Brand: MENABO
• Model: DELTA
• Item Model Number: 000096800000
• Item Weight: 2.87 pounds (approx. 1.3 kg)
• Package Dimensions: 11.81 x 8.66 x 2.56 inches (approx. 30 x 22 x 6.5 cm)
• Mounting Type: Roof Bars (for normal roofs)
• Compatibility: DODGE Journey 5p 08>11, FIAT Freemont 5p 11>, HONDA CR-V IV 5p 12>, MAZDA 2 λ5p 07>09, 3 / Axela (BK) 5p 03>09, MINI Cooper 3p 14>, Cooper S 3p 14>, One 3p 14>

Warranty and Support

For information regarding product warranty, please refer to the warranty card included with your purchase or visit the official MENABO website. For technical support, spare parts, or further assistance, please contact your retailer or MENABO customer service.

MENABO Official Website: www.menabo.it (Note: Link provided as an example, actual link may vary)