Utilitech 90CFM Decorative 4-in-1 Bath Fan

1. Introduction

This manual provides essential information for the safe installation, operation, and maintenance of your Utilitech 90CFM Decorative 4-in-1 Bath Fan, Model 7105-06. This unit integrates a powerful exhaust fan with an LED light, designed for bathroom environments. Please read these instructions thoroughly before beginning installation or operation.

2. Safety Information

WARNING: To reduce the risk of fire, electric shock, or injury to persons, observe the following:

• Read all instructions before installing or servicing this fan.
• Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.
• Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
• Before servicing or cleaning the unit, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
• Do not use this fan with any solid-state speed control device unless specifically approved for use with this model.
• This product is designed for general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
• Always ensure proper ventilation for combustion air needed for the safe operation of fuel-burning equipment to prevent back-drafting.

3. Package Contents

Verify that all components are present and undamaged before proceeding with installation. If any parts are missing or damaged, do not attempt to install the unit. Contact customer service for assistance.

• Bath Fan Unit with Integrated LED Light
• Mounting Hardware
• Remote Control
• Instruction Manual

4. Setup and Installation

Assembly is required for this product. Ensure power is disconnected at the circuit breaker before beginning installation.

4.1 Pre-Installation Checks

• Confirm the mounting location is suitable for a wall-mounted fixture and can support the unit's weight (approximately 5.8 pounds).
• Ensure adequate space for ducting and electrical connections.
• Verify that the electrical supply matches the fan's requirements (standard household voltage).

4.2 Mounting the Unit

1. Carefully unpack the bath fan unit.
2. Position the unit in the desired wall-mount location.
3. Secure the fan housing to the wall structure using the provided mounting hardware. Ensure the unit is firmly attached to prevent vibration and noise.

4.3 Electrical Connection

This unit is a corded electric device. All wiring must comply with local electrical codes.

1. Route the electrical wiring from the power source to the fan's junction box.
2. Connect the supply wires to the fan's wires according to the wiring diagram provided inside the junction box cover. Typically, this involves connecting live to live, neutral to neutral, and ground to ground.
3. Secure all wire connections with approved wire connectors.
4. Close the junction box cover securely.

4.4 Ducting Connection

1. Connect appropriate ductwork to the fan's exhaust port.
2. Ensure all duct connections are sealed with duct tape or clamps to prevent air leakage.
3. Route the ductwork to an approved exterior vent.

5. Operating Instructions

Once installed and power is restored, the bath fan can be operated using the included remote control.

5.1 Remote Control Operation

• Power Button: Press to turn the fan and light ON or OFF.
• Fan Button: Activates or deactivates the exhaust fan. The fan operates at 90 CFM with a sound level of 2.0 sones.
• Light Button: Controls the integrated 20-watt LED light. Press to turn the light ON or OFF.

Ensure the remote control has fresh batteries and is within range of the fan unit for proper operation.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your bath fan. Always disconnect power at the circuit breaker before performing any maintenance.

6.1 Cleaning the Grille and Fan Blades

1. Turn off power to the fan at the service panel.
2. Carefully remove the decorative grille from the fan housing.
3. Wipe the grille with a damp cloth and mild detergent. Rinse and dry thoroughly.
4. Gently wipe the fan blades and interior of the housing with a damp cloth to remove dust and debris. Do not immerse electrical parts in water.
5. Reattach the grille once all parts are dry.

6.2 LED Light Maintenance

The integrated 20-watt LED light is designed for long life, lasting up to 30,000 hours. Replacement of individual LED components is generally not required. If the light fails prematurely, contact customer support.

7. Troubleshooting

Before attempting any repairs, ensure power is disconnected at the circuit breaker.

8. Specifications

9. Warranty and Support

For warranty information or technical support, please refer to the documentation included with your purchase or contact Utilitech customer service. Keep your proof of purchase for warranty claims.