Introduction
This user manual provides comprehensive instructions for the installation, operation, and maintenance of your Goboost Cell Phone Signal Booster. Designed for home and office use, this amplifier repeater enhances GSM, 3G, 4G LTE, and 5G signals on Band 2 and Band 5, supporting major carriers like Verizon, AT&T, and T-Mobile. Please read this manual thoroughly before installation to ensure optimal performance and safety.
The Goboost Cell Phone Signal Booster kit, featuring the main booster unit, outdoor antenna, indoor antenna, and connecting coaxial cable.
Product Benefits
The Goboost signal booster helps reduce dropped calls, provides faster data speeds, improves 4G LTE voice quality, and offers high gain for safe home use.
What's in the Box
- 1 x Band 2 Band 5 Signal Booster (850/1900MHz)
- 1 x LPDA Antenna (Outdoor Antenna)
- 1 x Panel Antenna (Indoor Antenna)
- 1 x 13 Meters (43 feet) Coaxial Cable
- 1 x User Manual
- 1 x Power Supply
Setup Guide
Follow these steps for proper installation of your Goboost Cell Phone Signal Booster. Correct installation is crucial for optimal performance.
1. Pre-installation Signal Check
Before installing, it is important to verify your current indoor signal strength and ensure your cell phone band is supported by the booster (Band 2 and Band 5). This step helps confirm the booster's compatibility with your network and identifies areas with weak signals.
This video demonstrates how to check your current indoor signal strength using a mobile application. (Relevant segment: 0:04 - 0:15)
Instructions for testing your cell phone band on both iPhone and Android devices to ensure compatibility with the booster's supported bands (Band 2 and Band 5).
2. Outdoor Antenna Installation
The outdoor antenna (LPDA Antenna) should be installed in a location with the strongest possible signal, ideally on the roof or an elevated position, free from obstructions. Aim for a signal stronger than -80dB or at least 3 bars on your phone. Ensure the antenna is pointed towards the nearest cell tower.
This video demonstrates how to find the best signal location and install the outdoor antenna. (Relevant segment: 0:16 - 0:50)
System diagram showing the outdoor antenna receiving signal from the cell tower, transmitting it to the signal booster, which then amplifies and broadcasts it via the indoor antenna.
3. Indoor Antenna Installation
Install the indoor antenna (Panel Antenna) in the area where you need improved signal coverage. Ensure there is sufficient separation (at least 20 feet vertically or 50 feet horizontally) between the indoor and outdoor antennas to prevent signal oscillation.
This video demonstrates the installation of the indoor antenna. (Relevant segment: 0:51 - 1:00)
4. Connect the Booster Unit
Connect the coaxial cable from the outdoor antenna to the "BTS" port (Base Transceiver Station) on the booster unit. Connect the coaxial cable from the indoor antenna to the "MS" port (Mobile Station) on the booster unit. Finally, connect the power supply to the booster unit and plug it into a power outlet.
This video demonstrates connecting the antennas and power supply to the booster unit. (Relevant segment: 1:01 - 1:13)
The intelligent LCD display on the booster unit provides real-time signal strength information for both Band 2 and Band 5, along with power indicators.
5. Final Signal Test
Once all components are connected and powered on, observe the signal strength on your mobile device. You should notice a significant improvement in signal bars and data speeds.
This video shows a before and after comparison of signal strength after booster installation. (Relevant segment: 1:14 - 1:20)
Operating Instructions
Once installed, the Goboost signal booster operates automatically. The LCD display provides real-time feedback on signal gain and output. Ensure the booster remains powered on for continuous signal enhancement. The system is designed for multi-band and multi-carrier support, automatically adjusting to amplify signals on Band 2 (1900MHz) and Band 5 (850MHz).
The booster is compatible with all cellular devices and operates within specified frequency ranges for optimal performance.
The Goboost signal booster is suitable for various environments including homes, offices, basements, and rural areas.
Maintenance
The Goboost Cell Phone Signal Booster requires minimal maintenance. Keep the booster unit and antennas clean and free from dust. Periodically check all cable connections to ensure they are secure. Avoid placing the booster in direct sunlight or in areas with extreme temperatures or high humidity.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No Signal Improvement |
|
|
| Dropped Calls / Slow Data |
|
|
| Booster Overheating |
|
|
Specifications
- Model: B07N7YWFCS
- Brand: GOBOOST
- Frequency Band Class: Dual-Band (Band 2: 1900MHz, Band 5: 850MHz)
- Special Features: LCD Display, Multi-Band, Multi-Carrier Support
- Package Dimensions: 13.7 x 9.72 x 9.53 inches
- Item Weight: 5.61 pounds
- Color: LPDA/Panel
- Manufacturer: Goboost
- Date First Available: January 26, 2019
FCC compliance information and consumer device notice located on the back of the booster unit.
Warranty and Support
For warranty information and technical support, please refer to the official GOBOOST website or contact their customer service directly. Keep your purchase receipt for warranty claims.
GOBOOST is dedicated to helping every user improve their cell phone signal. If you encounter any signal problems, please feel free to contact GOBOOST customer support.
You can visit the official GOBOOST store for more information: GOBOOST Store
