iBeam by Metra TEDGH Ram Tailgate Handle Camera User Manual

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your iBeam by Metra TEDGH Ram Tailgate Handle Camera. This factory replacement tailgate handle camera is designed to enhance visibility behind your vehicle, offering a clear view for safer maneuvering and parking.

Product Overview

The iBeam TEDGH camera integrates seamlessly into your Ram truck's tailgate handle, providing a discreet and factory-like appearance. It features advanced imaging capabilities for both day and night use.

• High-Quality Imaging: Equipped with a 1/3 inch CMOS camera sensor for sharp and clear video output.
• Wide Viewing Angle: Offers a 150-degree viewing angle to capture a broad perspective behind the vehicle.
• Night Vision: Features 0.5 LUX night vision for improved visibility in low-light conditions.
• Defeatable Parking Lines: Includes on-screen parking guidelines that can be enabled or disabled as per user preference.
• Extended Harness: Comes with a 26-foot harness for flexible connection to an aftermarket radio or display (not included).

What's in the Box

Upon opening the product packaging, please ensure all the following components are present:

• iBeam TEDGH Ram Tailgate Handle Camera unit
• 26-foot extension cable harness
• User Manual (this document)

Setup and Installation

The iBeam TEDGH camera is designed for surface mount installation as a factory replacement tailgate handle. Professional installation is recommended.

Safety Precautions

• Disconnect the vehicle's battery before beginning installation to prevent electrical shorts.
• Ensure all wiring is routed away from moving parts, heat sources, and sharp edges.
• Verify all connections are secure and properly insulated.
• This product is intended for use with a 12-volt DC power supply.

Installation Steps (General Guide)

1. Remove Existing Tailgate Handle: Carefully remove the original tailgate handle from your Ram truck. Refer to your vehicle's service manual for specific instructions.
2. Install New Tailgate Handle Camera: Mount the iBeam TEDGH camera unit into the tailgate opening, ensuring it is securely fastened.
3. Route Wiring: Route the 26-foot extension cable from the camera through the tailgate and chassis to the location of your aftermarket radio or display. Ensure the cable is protected from damage.
4. Connect to Display: Connect the video output cable from the camera harness to the video input of your aftermarket radio or monitor.
5. Power Connection: Connect the power wires of the camera harness to a suitable 12-volt power source, typically the vehicle's reverse light circuit, so the camera activates when the vehicle is in reverse.
6. Test Functionality: Reconnect the vehicle's battery and test the camera's operation. Engage reverse gear and verify that the camera image appears on your display.
7. Secure Wiring: Once confirmed operational, secure all wiring with zip ties or electrical tape to prevent rattling or damage.

Figure 1: The iBeam TEDGH Ram Tailgate Handle Camera, showing the integrated camera lens on the left side of the handle and the attached wiring harness on the right.

Figure 2: A closer front view of the iBeam TEDGH Ram Tailgate Handle Camera, highlighting the camera lens and the handle mechanism.

Operating Instructions

The iBeam TEDGH camera operates automatically when the vehicle is placed into reverse gear, provided it is correctly wired to the reverse light circuit or a switched 12V source that activates with reverse.

• Automatic Activation: When you shift your vehicle into reverse, the camera will automatically display the rear view on your connected aftermarket monitor.
• Parking Lines: The camera features integrated parking lines to assist with judging distance and alignment. These lines are defeatable, meaning they can be turned on or off. The method for defeating (enabling/disabling) parking lines typically involves cutting a specific wire loop on the camera harness during installation. Consult the wiring diagram provided with the product for exact instructions.
• Night Vision: The 0.5 LUX night vision capability allows for clear visibility even in very low light conditions, enhancing safety during nighttime parking or maneuvering.

Maintenance

To ensure optimal performance and longevity of your iBeam TEDGH camera, follow these simple maintenance guidelines:

• Clean the Lens: Regularly clean the camera lens with a soft, damp cloth to remove dirt, dust, and debris that may obstruct the view. Avoid abrasive cleaners or materials that could scratch the lens.
• Inspect Wiring: Periodically check the wiring and connections for any signs of wear, fraying, or corrosion. Ensure all connections remain secure.
• Avoid High-Pressure Washing: When washing your vehicle, avoid directing high-pressure water jets directly at the camera lens or housing, as this could potentially damage the seal or internal components.

Troubleshooting

If you encounter issues with your iBeam TEDGH camera, refer to the following common troubleshooting steps:

Specifications

Warranty Information

iBeam products are manufactured by Metra Electronics Corp. For specific warranty details, including coverage period and terms, please refer to the warranty card included with your product or visit the official Metra Electronics website. Keep your proof of purchase for warranty claims.

Customer Support

Should you require further assistance, technical support, or have questions not covered in this manual, please contact Metra Electronics Corp. customer support. Contact information can typically be found on their official website or on the product packaging.

Manufacturer: Metra Electronics Corp