Brightech Parker

Brightech Parker LED Floor Lamp User Manual

Model: Parker (5C-AU1Y-1RXP)

Introduction

Thank you for purchasing the Brightech Parker LED Floor Lamp. This elegant 48-inch tall lamp features a beautiful neutral linen shade and a chic wooden base, designed to enhance the ambiance of your living room, bedroom, office, or meditation space. This manual provides essential information for the safe and proper assembly, operation, and maintenance of your new lamp.

Important Safety Instructions

Please read all instructions carefully before assembly and use. Keep this manual for future reference.

Ensure the power is off before installing or replacing bulbs.
Do not use bulbs exceeding the specified wattage.
Do not operate the lamp with a damaged cord or plug.
Keep the lamp away from water and moisture.
This lamp is for indoor use only.
Always unplug the lamp from the electrical outlet before cleaning.
Do not attempt to modify or repair the lamp yourself. Contact qualified service personnel for repairs.

Package Contents

Verify that all components are present and undamaged before beginning assembly:

Lamp Shade (Linen)
Wooden Base Sections (typically 3-4 pieces)
Lamp Pole Sections (typically 3-4 pieces with threaded rods)
Lamp Socket Assembly with Power Cord and Foot Switch
LED Bulbs (2 x 9.5W E26)
Shade Support Ring/Harp
Finial (for securing shade)

Setup and Assembly

Follow these steps to assemble your Brightech Parker LED Floor Lamp:

Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, flat surface. Ensure all components listed in the "Package Contents" section are present.
Assemble Lamp Pole: The lamp pole consists of several sections with threaded rods. Gently screw these sections together clockwise until they are securely connected. Ensure the power cord passes freely through the pole as you assemble it.
Attach Base: Screw the assembled lamp pole into the wooden base. Ensure it is tightened securely to prevent wobbling.
Install Shade Support: Attach the shade support ring (harp) to the lamp socket assembly, if not already pre-attached.
Position Lamp Shade: Carefully place the linen lamp shade over the shade support. The shade is designed to sit snugly around the wooden base.
Secure Shade: If your lamp includes a finial, screw it onto the top of the lamp socket assembly to secure the shade in place.
Install Bulbs: Screw the two provided 9.5W E26 LED bulbs into the lamp sockets. Do not overtighten.
Connect to Power: Plug the lamp's power cord into a standard electrical outlet.

Brightech Parker LED Floor Lamp dimensions — Image: Overall dimensions of the Brightech Parker LED Floor Lamp, showing its 48-inch height and 10-inch base width.

Brightech Parker LED Floor Lamp wooden base — Image: Close-up view of the lamp's wooden base, illustrating its sturdy construction and design.

Brightech Parker LED Floor Lamp shade attachment — Image: Detail of the lamp's top section, showing how the shade is supported and secured.

Operating Instructions

The Brightech Parker LED Floor Lamp is designed for simple operation:

Power On/Off: Locate the foot switch on the power cord. Press the switch with your foot to turn the lamp on or off.
Bulb Replacement:
1. Ensure the lamp is unplugged from the power outlet and the bulbs have cooled down.
2. Carefully unscrew the old bulbs from the sockets.
3. Screw in new E26 base LED bulbs. The lamp is designed for two 9.5W LED bulbs, but can also accommodate incandescent or halogen bulbs up to a certain wattage (refer to lamp socket for maximum wattage if not using provided LEDs).
4. Plug the lamp back into the outlet.

Care and Maintenance

To ensure the longevity and appearance of your lamp, follow these maintenance guidelines:

Cleaning: Unplug the lamp before cleaning. Use a soft, dry cloth to wipe down the wooden base and lamp shade. Do not use abrasive cleaners or polishes, as they may damage the finish.
Bulb Care: The included LED bulbs are long-lasting (up to 20,000 hours). Avoid touching the bulbs directly with bare hands, as oils can reduce their lifespan.
Cord Inspection: Periodically inspect the power cord and plug for any signs of damage. If damaged, discontinue use and contact customer support.

Troubleshooting

If you encounter issues with your Brightech Parker LED Floor Lamp, refer to the following common problems and solutions:

Problem	Possible Cause	Solution
Lamp does not turn on.	Not plugged in. Loose bulb. Faulty outlet. Damaged cord/switch. Burned out bulb.	Ensure the lamp is securely plugged into a working outlet. Tighten the bulbs in their sockets. Test the outlet with another appliance. Inspect the cord and foot switch for damage. If damaged, do not use. Replace bulbs with new ones.
Lamp flickers.	Loose bulb. Incompatible dimmer (if applicable). Faulty bulb.	Tighten the bulbs. Ensure the lamp is not connected to an incompatible dimmer switch. Try a different bulb to see if the issue persists.
Lamp is wobbly.	Loose pole sections or base connection.	Ensure all lamp pole sections and the base connection are securely tightened.

If the problem persists after trying these solutions, please contact Brightech customer support.

Specifications

Feature	Detail
Model Name	Parker
Model Number	5C-AU1Y-1RXP
Dimensions (H x W x D)	Approx. 48 inches (121.9 cm) H x 10 inches (25.4 cm) W x 10 inches (25.4 cm) D
Weight	4.2 Kilograms
Bulb Type	LED (2 x 9.5W included)
Bulb Base	E26
Switch Type	Foot Switch
Shade Material	Acrylic / Linen
Base Material	Wood
Color	Beige

Warranty and Support

Brightech offers an industry-leading 3-year limited warranty on all purchases from Brightech CA. This warranty covers defects, malfunctions, or sudden failures of your standing lamp.

If you experience any trouble with your Brightech Parker LED Floor Lamp, please do not hesitate to reach out to our customer support team for assistance. For warranty claims or technical support, please visit the official Brightech website or contact their customer service directly.

For more information, visit the Brightech Store on Amazon.