Mylek 2kW Electric Heater Instruction Manual

Introduction

Thank you for purchasing the Mylek 2kW Electric Heater. This manual provides essential information for the safe and efficient operation of your appliance. Please read these instructions thoroughly before installation and use, and retain them for future reference.

Important Safety Instructions

WARNING: To avoid overheating, do not cover the heater.

• Ensure the voltage indicated on the rating label matches your mains supply.
• This appliance is for indoor use only.
• Do not use this heater in the immediate surroundings of a bath, a shower, or a swimming pool.
• Keep flammable materials such as furniture, curtains, and other combustible items at least 1 meter (3 feet) from the front and sides of the heater.
• Do not operate the heater with a damaged cord or plug, or after the heater malfunctions or has been dropped or damaged in any manner.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• The heater is equipped with an overheat protection feature. If the heater overheats, it will automatically shut off. Unplug the heater and allow it to cool down for 30 minutes before restarting.

Product Overview

The Mylek 2kW Electric Heater is designed for efficient heating with advanced features for user convenience and safety.

Key Features:

• 2 Heat Settings (1kW and 2kW)
• PTC Ceramic Heating Element
• Adjustable Thermostat (5°C to 35°C)
• 7-Day Programmable Timer
• Remote Control Operation
• Digital Display
• Overheat Protection
• Fan-only setting for warmer months

Image 1: Front view of the Mylek 2kW Electric Heater with its remote control. The heater is white with a digital display on the right side and a fan outlet below. The remote control has various buttons for power, settings, and timer functions.

Image 2: This image highlights key features of the Mylek 2kW Electric Heater. It shows a close-up of the digital display, an illustration of wide air flow distribution, the remote control, and icons indicating two heat settings and one cooling setting (fan-only mode).

Image 3: A detailed view of the remote control for the Mylek 2kW Electric Heater. Buttons are clearly labeled for functions such as TIME ON, EDIT, TIME OFF, DAY, OK, P (Program), +, -, SET, and Power.

Setup and Installation

Mounting the Heater:

1. Choose Location: Select a suitable wall location, ensuring it is at least 1 meter (3 feet) away from any flammable materials and not directly above or below a power outlet. The power cable exits from the right-hand side when facing the heater.
2. Mark Drill Holes: Hold the heater against the wall at the desired mounting height. Mark the positions for the mounting screws. Note that there is no template provided, so careful measurement is required. The mounting holes are designed for the heater to slide over and then secure.
3. Drill and Insert Plugs: Drill holes at the marked positions and insert appropriate wall plugs (not supplied).
4. Secure Heater: Screw the mounting screws into the wall plugs, leaving a small gap. Carefully align the heater's mounting slots with the screws and slide the heater down to secure it. Tighten the screws to ensure the heater is firmly attached to the wall.

Initial Power-On:

1. Ensure the heater is securely mounted.
2. Plug the power cord into a suitable 230V AC mains socket. The supplied cable is approximately 60 cm long.
3. The heater will enter standby mode.

Operating Instructions

Control Panel and Remote Control:

The heater can be operated using the control panel on the unit or the supplied remote control. The remote control offers full functionality.

Basic Operation:

1. Power On/Off: Press the Power button () on the remote control or the unit's control panel to turn the heater on or off.
2. Heat Settings: Once powered on, press the SET button to cycle through heat settings:
   • 1kW: Low heat output.
   • 2kW: High heat output.
   • Fan Only: Circulates air without heating.
3. Temperature Adjustment: Use the + and - buttons to set the desired room temperature (range: 5°C to 35°C). The heater will automatically adjust its operation to maintain the set temperature.

Timer and Program Settings:

The heater features a 7-day programmable timer with up to 6 different settings per day.

1. Setting Current Time and Day:
   • Press the DAY button to set the current day of the week.
   • Press the TIME ON or TIME OFF buttons, then use + and - to adjust the hour and minute. Press OK to confirm.
2. Programming On/Off Times:
   • Press the P (Program) button. The display will show "P1".
   • Use DAY to select the day(s) for the program.
   • Use TIME ON and TIME OFF buttons, along with + and -, to set the desired on and off times for the program.
   • Press SET to choose the heat setting (1kW, 2kW, or Fan Only) for this program period.
   • Press OK to confirm and move to the next program (P2, P3, etc.). Repeat for up to 6 programs per day.
3. Activating Program Mode: After setting programs, ensure the heater is in program mode (indicated by a specific icon on the display, refer to the full manual for details) for the timer settings to take effect.

Open Door Detection:

This feature automatically switches the unit to standby if a sudden drop in temperature is detected, helping to save energy. This is particularly useful when installed above internal doors in offices or receptions. This feature can be manually switched off if the heater is used over an external door that is frequently opened.

Maintenance and Storage

Cleaning:

1. Always unplug the heater from the power outlet and allow it to cool completely before cleaning.
2. Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
3. Do not immerse the heater in water or any other liquid.
4. Periodically clean the air inlet and outlet grilles with a vacuum cleaner to remove dust and lint.

Storage:

If the heater is not going to be used for an extended period, store it in a cool, dry place, preferably in its original packaging, away from direct sunlight and moisture.

Troubleshooting

Specifications

Warranty and Support

For warranty information or technical support, please refer to the documentation provided with your purchase or contact the retailer/manufacturer directly. Keep your proof of purchase for any warranty claims.

Manufacturer: Sales Direct Online