1. Introduction
This manual provides comprehensive instructions for the safe installation, operation, and maintenance of your Amico 3 Head LED Security Light with Motion Sensor. Please read this manual thoroughly before installation and retain it for future reference. Proper installation and adherence to safety guidelines are crucial for optimal performance and user safety.
Safety Information
- Always turn off power at the circuit breaker before installation or servicing.
- Installation should be performed by a qualified electrician or a person familiar with the construction and operation of the product and the hazards involved.
- Ensure all electrical connections comply with local codes and ordinances.
- Do not install on surfaces that are not structurally sound.
- Avoid looking directly into the LED light source when illuminated.
2. Product Features
The Amico 3 Head LED Security Light is designed for outdoor use, offering adjustable lighting and motion detection capabilities.
- High Brightness & Energy Efficiency: Outputs 40W, 4000 Lumens, 5000K (Daylight White) equivalent to 200W halogen light, reducing electricity consumption.
- Three Lighting Modes: Features Motion Detection, Dusk-to-Dawn (D2D), and Always-On modes for versatile operation.
- Adjustable Motion Sensor: 180-degree swiveling angle with a detection distance of up to 75 feet.
- Durable & Weatherproof: IP65 waterproof rating protects against rain, sleet, or snow. Constructed with aluminum for excellent heat dissipation and extended lifespan.
- Adjustable Light Heads: Three independently adjustable light heads allow for broad and customized light coverage.
3. Package Contents
Verify that all components are present before beginning installation:
- Amico 3 Head LED Security Light Unit
- Mounting Bracket
- Mounting Screws
- Wire Nuts
- EVA Pad (for waterproofing)
- Instruction Manual
4. Installation Instructions
Follow these steps for a secure and functional installation. Ensure power is OFF at the circuit breaker before starting.
- Prepare the Mounting Surface: Ensure the junction box is securely installed and accessible.
- Install Mounting Bracket: Fasten the provided mounting bracket to the existing junction box using the supplied screws. Ensure it is firmly attached.
- Pass Wires Through EVA Pad: Carefully thread the electrical wires from the light fixture through the center hole of the EVA pad. This pad helps create a waterproof seal.
- Wire Connections: Connect the wires from the light fixture to the corresponding wires from the junction box using the wire nuts.
- Green wire (from light) to Green wire (ground from junction box)
- Black wire (from light) to Black wire (hot from junction box)
- White wire (from light) to White wire (neutral from junction box)
Note: Improper wiring may cause the light to be slightly bright even when off.
- Mount the Light Fixture: Align the light fixture with the mounting bracket. Pass the screw through the hole on the light body, align with the hole in the mounting bracket, and tighten securely.
- Seal the Hole: Block the screw hole with the provided rubber plug to maintain the light's waterproof integrity.
- Adjust Light Heads and Sensor: Adjust the three light heads and the motion sensor to your desired angles for optimal coverage.
Installation Video Guide
This video demonstrates the step-by-step installation process for the Amico Security Light, including mounting the bracket, wiring connections, and securing the light fixture.
5. Operating Modes
The Amico Security Light offers three distinct operating modes, controlled by switches and dials on the motion sensor unit. Refer to the diagram below for control locations.
Mode Settings:
- Motion Detection Mode: The light activates when motion is detected within its range and turns off after a set time. Adjust the 'DISTANCE' dial to H (High), M (Medium), or L (Low) for sensitivity, and the 'TIME' dial to 1, 3, or 10 minutes for illumination duration.
- Dusk-to-Dawn (D2D) Mode: The light automatically turns on at dusk and off at dawn. To activate, set the 'DISTANCE' dial to 'D2D' and the 'TIME' dial to your desired duration (1, 3, or 10 minutes). The light will remain on for the set duration after dusk.
- Always-On Mode: For continuous illumination, set the 'DISTANCE' dial to 'D2D' and the 'TIME' dial to 'TEST'. The light will remain on until manually switched off or the settings are changed. This mode can also be controlled by a wall switch.
Operating Modes Video Guide
This video illustrates the three operational modes of the Amico Security Light: Always-on, Dusk-to-Dawn, and Motion-Activated, showing how to set each mode.
6. Maintenance
Regular maintenance ensures the longevity and optimal performance of your security light.
- Cleaning: Periodically clean the light heads and motion sensor lens with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Inspection: Annually inspect the wiring and mounting for any signs of wear, damage, or loose connections. Ensure the waterproof seals are intact.
- Environmental Factors: Keep the motion sensor clear of obstructions like tree branches or debris that could interfere with its detection capabilities.
7. Troubleshooting
If you encounter issues with your Amico Security Light, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power, incorrect wiring, sensor malfunction, ambient light too high. | Check circuit breaker. Verify wiring connections. Adjust sensor sensitivity. Ensure D2D mode is not active during daylight. |
| Light stays on continuously. | Sensor in 'TEST' mode, continuous motion, incorrect wiring. | Check sensor mode settings. Ensure no constant motion in detection zone. Re-check wiring. |
| Light turns on for no apparent reason. | High sensor sensitivity, environmental factors (wind, small animals). | Reduce sensor 'DISTANCE' setting. Clear obstructions from detection zone. |
| Light flashes or flickers. | Loose wiring, power fluctuations, faulty unit. | Check all wire connections. Consult an electrician for power issues. Contact customer support if problem persists. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Amico |
| Model Name | PD-1711 |
| Power Source | Corded Electric |
| Wattage | 40 watts |
| Brightness | 4000 Lumens |
| Color Temperature | 5000 Kelvin (Day Light White) |
| Material | Aluminum |
| Water Resistance Level | IP65 (Water Resistant) |
| Motion Sensor Angle | 180 degrees |
| Motion Detection Distance | Up to 75 feet |
| Installation Type | Wall Mount |
| Product Dimensions | 13.8"L x 6"W x 6.7"H |
| Item Weight | 2.51 pounds |
9. Warranty Information
The Amico 3 Head LED Security Light (Model PD-1711) comes with a 5-year limited warranty. For specific terms and conditions, please refer to the warranty card included in your product packaging or contact Amico customer support.
10. Customer Support
For any questions, technical assistance, or warranty claims, please contact Amico customer support through the official Amico website or the contact information provided in your product packaging.
