Flamaker 4-Piece Outdoor Patio Bistro Set

Important Safety Information

Please read and understand all instructions before assembly and use. Keep this manual for future reference.

• Do not exceed the maximum weight capacity of 330 pounds per seating unit.
• Exercise caution around sharp edges during the assembly process.
• This furniture is not heat-resistant. Avoid placing hot items directly on surfaces without protection.
• Ensure all bolts and screws are securely tightened before use. Periodically check and re-tighten as necessary.
• Place the furniture on a flat, stable surface to prevent tipping.

Package Contents

Verify that all components listed below are present before beginning assembly. If any parts are missing or damaged, please contact customer support.

Image: Overview of all components and hardware for assembly.

Parts List:

• 1 x Loveseat Frame
• 2 x Single Chair Frames
• 1 x Coffee Table Frame
• 1 x Tempered Glass Tabletop
• Textilene Fabric for Loveseat Seat and Back
• Textilene Fabric for Single Chair Seats and Backs (2 sets)

Hardware List:

• Bolts (various sizes)
• Washers
• Nuts
• Allen Wrench (Assembly Tool)
• Suction Cups for Glass Tabletop
• Screw Full Covers

Assembly Instructions

Follow these steps carefully to assemble your Flamaker 4-Piece Outdoor Patio Bistro Set. It is recommended to assemble on a soft, clean surface to prevent scratches.

Step 1: Assemble the Single Chairs

1. Attach the backrest frame to the seat frame using the provided bolts and washers. Do not fully tighten yet.
2. Connect the armrests to the assembled seat and backrest. Ensure all holes align.
3. Once all components are loosely connected, place the chair on a flat surface and gradually tighten all bolts evenly.
4. Install the screw full covers over exposed bolt heads for a finished look and protection.

Image: Step-by-step assembly for a single chair.

Step 2: Assemble the Loveseat

1. Attach the two backrest sections to the loveseat seat frame using the appropriate bolts and washers.
2. Connect the side armrest frames to the main loveseat structure.
3. Ensure all parts are aligned, then place the loveseat on a flat surface and tighten all bolts securely and evenly.
4. Apply screw full covers to all exposed bolt heads.

Image: Step-by-step assembly for the loveseat.

Step 3: Assemble the Coffee Table

1. Attach the four legs to the table frame using the provided hardware. Do not fully tighten.
2. Ensure the frame is stable and level, then tighten all bolts.
3. Place the suction cups into the designated holes on the table frame.
4. Carefully place the tempered glass tabletop onto the suction cups, ensuring it is centered and secure.

Image: Step-by-step assembly for the coffee table.

Care and Maintenance

Proper care will extend the life and appearance of your patio set.

• Cleaning: Wipe with a damp cloth for general cleaning. For stubborn dirt, a mild soap solution can be used, followed by rinsing with clean water and drying thoroughly.
• Textilene Fabric: The breathable Textilene material is easy to clean. Simply wipe it down with a damp cloth.
• Powder-Coated Steel Frame: The powder-coated finish helps resist rust. Clean with a damp cloth. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
• Glass Tabletop: Clean with a standard glass cleaner and a soft cloth.
• Seasonal Storage: During harsh weather conditions (heavy rain, snow, extreme cold), it is recommended to store the furniture indoors or cover it with a protective outdoor furniture cover to prevent damage and prolong its lifespan.
• Regular Inspection: Periodically check all bolts and connections to ensure they remain tight. Re-tighten as needed to maintain stability and safety.

Troubleshooting

If you encounter issues during assembly or use, refer to the following common solutions:

• Wobbly Table/Chairs: Ensure all bolts are fully and evenly tightened. Sometimes, loosening all bolts slightly, placing the furniture on a flat surface, and then tightening them in a cross-pattern can help level the unit. Check that all protective feet are properly installed.
• Difficulty Aligning Holes: Do not fully tighten any bolts until all components are loosely assembled. This allows for minor adjustments. If a hole is severely misaligned, check if a part is oriented incorrectly.
• Missing or Damaged Parts: If any parts are missing or damaged upon arrival, do not proceed with assembly. Contact Flamaker customer support immediately for assistance.
• Scratches on Floor: The chairs feature a bending design for easy movement. Ensure you lift the chairs rather than dragging them to prevent scratches on your floor or patio surface.

Specifications

Image: Dimensions of the Flamaker 4-Piece Outdoor Patio Bistro Set components.

Warranty and Support

For warranty information, please refer to the documentation included with your product packaging or contact Flamaker customer support directly. Flamaker offers various protection plans for extended coverage, which can be found on the product's purchase page.

If you require assistance with assembly, missing parts, or have any questions regarding your Flamaker 4-Piece Outdoor Patio Bistro Set, please contact Flamaker customer service. You can often find contact details on the manufacturer's website or through your retailer.

For additional product information and to explore other Flamaker products, visit the official Flamaker Store online.