BNT Dummy Fake Security Camera (Model BNT-K8FaCam-2PW) Instruction Manual

1. Introduction

The BNT Dummy Fake Security Camera is designed to provide a realistic visual deterrent against potential intruders. Its appearance closely mimics that of a functional surveillance camera, aiming to reduce the likelihood of criminal activity by creating the impression of active monitoring. This manual provides essential information for the proper setup, operation, and maintenance of your dummy camera.

Image 1.1: Two BNT white dummy fake security cameras, showcasing their realistic design.

2. What's in the Box

Upon opening your package, you should find the following components:

• BNT Bullet Simulation Fake Camera (White) x 2
• Screws for installation
• User Manual (this document)
• Warning Security Alert Sticker Decal x 2

Image 2.1: Package contents showing two dummy cameras, warning stickers, and screws.

3. Features

• Realistic Design: Mimics the appearance of a real surveillance camera.
• Flashing LED Light: Features a built-in red LED light that illuminates at night, simulating active recording.
• Photoelectric Sensor: Automatically activates the red LED light in low-light conditions.
• Durable Construction: Made from Acrylonitrile Butadiene Styrene (ABS) for indoor and outdoor use.
• Weatherproof: IP65 International Protection Rating ensures resistance to water.
• Easy Installation: No wiring required, mounts easily to ceilings or walls.
• Adjustable Angle: Features 2-axis rotation for flexible positioning (360-degree rotation, 90-degree tilt).
• Power Source: Operates on 2 AA batteries (not included).

Image 3.1: Close-up of the dummy camera's front, showing the dummy lens, red LED, and rotation capabilities.

4. Setup & Installation

4.1. Battery Installation

1. Locate the battery compartment on the camera. This is typically found by sliding open the back cover.
2. Insert 2 AA batteries (not included) into the compartment, ensuring correct polarity (+/-).
3. Close the battery compartment securely.

Image 4.1: Illustration of battery insertion into the dummy camera.

4.2. Mounting the Camera

The camera can be easily installed on a ceiling or wall using the provided screws. No complex wiring is necessary.

1. Choose a suitable location for installation, considering visibility and desired deterrent effect.
2. Position the mounting base against the surface and mark the screw holes.
3. Drill pilot holes if necessary, then secure the mounting base with the provided screws.
4. Attach the camera to the mounted base.
5. Adjust the camera's angle using its 2-axis rotation feature to achieve the desired coverage.

Video: BNT Dummy Fake Security Camera Overview

Video 4.2.1: This video provides a general overview of the BNT Dummy Fake Security Camera, highlighting its features and realistic appearance.

Video: Protecting Property with Fake Cameras

Video 4.2.2: This video demonstrates how fake cameras can be used to enhance property security and deter potential threats.

5. Operating Instructions

The BNT Dummy Fake Security Camera is designed for simple, autonomous operation:

• Once batteries are installed, the built-in photoelectric sensor will detect ambient light levels.
• During daylight hours, the red LED light will remain off.
• As darkness falls, the photoelectric sensor will automatically activate the red LED light, causing it to illuminate. This simulates the operation of a real security camera's night vision or recording indicator.
• The camera provides 24/7 visual deterrence without any manual intervention after initial setup.

Image 5.1: The dummy camera's red LED light is active at night, providing a visual deterrent.

6. Maintenance

• Battery Replacement: When the red LED light dims or stops illuminating, it is time to replace the batteries. Ensure to use high-quality AA batteries to prevent leakage and damage to the battery case.
• Environmental Protection: When replacing batteries, take care to avoid exposing the internal components to rain or moisture to maintain the lifespan of the battery case.
• Disposal: Please dispose of used batteries properly according to local regulations to protect the environment.
• Cleaning: Periodically wipe the camera's exterior with a soft, damp cloth to remove dust and debris. Avoid using harsh chemicals.

7. Troubleshooting

7.1. LED Light Not Illuminating at Night

• Check Batteries: Ensure that 2 AA batteries are correctly installed and are not depleted. Replace if necessary.
• Test Photoelectric Sensor: In a dark environment, cover the LED light with your hand. If the red LED light turns on, the product is functioning correctly. If it does not, check battery installation again.
• Environmental Factors: Ensure the camera is not installed in an area with ambient light at night (e.g., streetlights, porch lights) that might prevent the photoelectric sensor from detecting sufficient darkness to activate the LED.

8. Specifications

9. Warranty & Support

BNT provides reliable 24-month after-sales service for this product. If you have any questions, concerns, or require assistance with your BNT Dummy Fake Security Camera, please contact our dedicated customer service team. We are committed to ensuring your satisfaction.