Introduction
Thank you for choosing the Elica 42-inch Stainless Steel Professional Wall Mount Range Hood. This manual provides essential information for the safe installation, operation, and maintenance of your new appliance. Please read these instructions thoroughly before installation and use, and retain them for future reference. Proper installation and adherence to these guidelines will ensure optimal performance and longevity of your range hood.
Important Safety Information
WARNING: To reduce the risk of fire, electric shock, or injury to persons, observe the following:
- Install this range hood in accordance with all specified instructions.
- Always disconnect power to the range hood at the circuit breaker or fuse box before servicing.
- Ensure proper ventilation is provided for combustion gases from fuel-burning equipment to prevent back-drafting.
- Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
- Clean grease filters frequently. Grease should not be allowed to accumulate on the fan or filters.
- Never leave surface units unattended at high settings. Boil-overs cause smoking and greasy spill-overs that may ignite.
- Use appropriate size cookware. Always use cookware appropriate for the size of the surface element.
- This appliance is for indoor residential use only.
CALIFORNIA PROPOSITION 65 WARNING:
This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Package Contents
Verify that all components are present and undamaged before beginning installation. If any items are missing or damaged, contact Elica customer support.
- Range Hood Assembly
- Baffle Filters (pre-installed)
- Mounting Hardware (screws, anchors)
- Duct Transition Piece
- User Manual (this document)
Setup and Installation
Professional installation is recommended for this appliance. Ensure all local codes and ordinances are followed. Refer to the provided diagram for typical installation measurements.
1. Site Preparation
- Determine the desired mounting height. Elica recommends 24-30 inches above the cooking surface for optimal performance.
- Ensure adequate structural support in the wall for the range hood's weight.
- Verify electrical supply (120V, 60Hz, dedicated circuit recommended).
- Plan ductwork routing. This hood requires a 6-inch round duct.
2. Mounting the Hood
Carefully lift the range hood into position. Mark and drill pilot holes for the mounting screws. Secure the hood to the wall using the provided hardware. Ensure the hood is level before tightening all fasteners.
Figure 1: Elica 42-inch Stainless Steel Professional Wall Mount Range Hood installed in a kitchen setting. This image illustrates the typical appearance and placement of the range hood above a cooking range, integrated with kitchen cabinetry.
3. Ducting Connection
Connect the ductwork to the range hood's exhaust outlet. Use aluminum foil tape to seal all duct joints to prevent air leaks. Ensure the duct run is as short and straight as possible for maximum efficiency.
4. Electrical Connection
A qualified electrician should perform the electrical connection. Connect the range hood to a grounded 120V, 60Hz power supply. Follow all local electrical codes.
Operating Instructions
Your Elica range hood features intuitive knob controls for fan speed and lighting.
1. Fan Operation
Figure 2: Front view of the Elica range hood, highlighting the control knobs and integrated LED lighting. The baffle filters are visible underneath.
The range hood is equipped with two control knobs. One knob controls the fan speed. Rotate the knob clockwise to increase the fan speed from low to high. Rotate counter-clockwise to decrease speed or turn off the fan.
Figure 3: Close-up view of the backlit control knobs. When activated, the knobs illuminate with a blue light, indicating power and function.
2. Lighting Operation
The second knob controls the LED lighting. Rotate this knob to turn the lights on or off. The integrated LED lights provide bright illumination for your cooking surface.
Figure 4: Angled view showing the control panel with both the fan speed and light control knobs, along with the LED lights providing illumination.
Figure 5: Close-up view of the control knobs when the backlighting is off, showing their flush design.
Maintenance
Regular maintenance ensures optimal performance and extends the life of your range hood.
1. Cleaning Baffle Filters
The stainless steel baffle filters should be cleaned regularly, ideally every 3-6 weeks depending on cooking frequency. To remove:
- Ensure the range hood is off and cool.
- Locate the release latches on each filter.
- Pull the latch and carefully lower the filter.
- Wash filters in hot soapy water or in a dishwasher.
- Allow filters to dry completely before re-installing.
2. Cleaning Stainless Steel Surfaces
Clean the exterior surfaces with a soft cloth and a non-abrasive stainless steel cleaner. Always wipe in the direction of the grain to prevent scratching. Avoid using abrasive pads or harsh chemicals.
3. LED Light Replacement
LED lights are designed for long life and typically do not require frequent replacement. If a light fails, contact Elica customer support for replacement parts and instructions.
Troubleshooting Guide
Before contacting customer support, please refer to the following table for common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Hood does not operate | No power supply; Circuit breaker tripped; Loose wiring | Check power connection; Reset circuit breaker; Consult an electrician |
| Poor suction | Clogged filters; Restricted ductwork; Incorrect mounting height | Clean or replace filters; Check duct for obstructions; Verify mounting height |
| Excessive noise | Loose fan blades; Obstruction in fan; Improper installation | Inspect fan for debris; Ensure secure mounting; Contact service if issue persists |
| Lights not working | Light switch off; Faulty LED module | Turn on light switch; Contact Elica support for replacement LED module |
Product Specifications
| Feature | Detail |
|---|---|
| Model Number | B07LD1MJZC |
| Dimensions | 42 inches (Width) |
| Material | Stainless Steel |
| Mounting Type | Wall Mount |
| Air Flow Capacity | 1200 Cubic Feet Per Minute (CFM) |
| Controls Type | Knob |
| Voltage | 120 Volts |
| Light Source Type | LED |
| Filter Type | Mesh (Baffle) |
Warranty Information
Elica products are manufactured to the highest quality standards. For specific warranty terms and conditions applicable to your range hood, please refer to the warranty card included with your purchase or visit the official Elica website. Retain your proof of purchase for warranty claims.
Customer Support
If you have any questions, require technical assistance, or need to order replacement parts, please contact Elica customer support. Have your model number (B07LD1MJZC) and date of purchase ready when contacting support.
For the most up-to-date contact information, please visit the official Elica website or refer to your purchase documentation.
