Introduction
Thank you for choosing the Elica 34" Professional Insert Range Hood. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new appliance. Please read this manual thoroughly before using the range hood and retain it for future reference.
Safety Information
WARNING: To reduce the risk of fire, electric shock, or injury to persons, observe the following:
- Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
- Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel-burning equipment to prevent back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
- When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
- Ducted fans must always be vented to the outdoors.
- Always disconnect power from the range hood before servicing or cleaning.
- Never operate the range hood without the filters in place.
Package Contents
Verify that all components are present before beginning installation. If any items are missing or damaged, contact Elica customer service.
- Elica 34" Professional Insert Range Hood unit
- Baffle Filters
- Installation Hardware (screws, anchors, etc.)
- User Manual
Specifications
| Feature | Specification |
|---|---|
| Model | 34" Professional Insert Range Hood |
| Air Flow Capacity | 1200 Cubic Feet Per Minute (CFM) |
| Material | Stainless Steel |
| Controls Type | Knob |
| Light Source Type | LED |
| Filter Type | Mesh (Baffle) |
| Item Form | Insert |
| Ventilation Type | Ducted/Vented |
| Product Dimensions (D x W x H) | 34.5" x 22" x 11.5" |
| UPC | 190603002287 |
Installation and Setup
Proper installation is crucial for the performance and safety of your range hood. It is highly recommended that installation be performed by a qualified professional.
Pre-Installation Checklist:
- Ensure the mounting surface is structurally sound and can support the weight of the range hood.
- Verify that the electrical supply meets the requirements specified on the product label.
- Confirm ductwork is properly sized and routed for outdoor venting.
- Unpack the range hood and inspect for any shipping damage.
General Installation Steps (Consult full installation guide for detailed instructions):
- Prepare the Opening: Create the necessary opening in the cabinet or ceiling according to the dimensions provided in the detailed installation guide.
- Mount the Unit: Secure the range hood insert into the prepared opening using the provided mounting hardware. Ensure it is level and firmly attached.
- Connect Ductwork: Connect the range hood's exhaust outlet to the existing ductwork. Ensure all connections are sealed to prevent air leaks.
- Electrical Connection: Connect the range hood to a grounded electrical outlet or junction box, following local electrical codes.
- Install Filters: Insert the baffle filters into their designated slots.
- Test Operation: Restore power and test all functions (fan speeds, lights) to ensure proper operation.
Operating Instructions
The Elica Professional Insert Range Hood features intuitive knob controls for fan speed and lighting.
Fan Operation:
- Locate the right knob on the control panel. This knob controls the fan speed.
- Turn the knob clockwise to select desired fan speed: 1 (low), 2 (medium), 3 (high).
- Turn the knob counter-clockwise to the "OFF" position to turn off the fan.
- For optimal performance, turn on the range hood a few minutes before cooking and leave it on for several minutes after cooking to clear residual smoke and odors.
Light Operation:
- Locate the left knob on the control panel. This knob controls the LED lighting.
- Turn the knob clockwise to the "ON" position to illuminate the cooking surface.
- Turn the knob counter-clockwise to the "OFF" position to turn off the lights.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your Elica range hood.
Cleaning the Baffle Filters:
- Frequency: Clean filters regularly, typically every 3-6 weeks depending on cooking habits.
- Removal: Ensure the range hood is off. Grasp the filter handle and pull down to release it from the spring clips.
- Cleaning Method:
- Dishwasher: Most baffle filters are dishwasher safe. Place them in the dishwasher and run a normal cycle.
- Hand Wash: Soak filters in hot water with a degreasing detergent. Scrub gently with a non-abrasive brush if necessary. Rinse thoroughly and allow to dry completely before reinstallation.
- Reinstallation: Align the filter with the slots and push up until it clicks into place.
Cleaning the Exterior:
- Wipe the stainless steel surfaces with a soft cloth dampened with warm water and a mild detergent.
- For stubborn stains, use a stainless steel cleaner, applying it with a soft cloth and wiping in the direction of the grain.
- Do not use abrasive cleaners, steel wool, or scouring pads, as these can scratch the surface.
LED Light Replacement:
- LED lights are designed for long life and typically do not require frequent replacement.
- If a light fails, contact Elica customer support for assistance with replacement parts and instructions.
Troubleshooting
Before contacting customer service, review the following common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Range hood does not turn on. | No power supply; tripped circuit breaker; loose wiring. | Check power connection. Reset circuit breaker. Verify wiring connections (consult a qualified electrician). |
| Poor suction performance. | Clogged filters; restricted ductwork; incorrect installation height. | Clean or replace filters. Check ductwork for obstructions or kinks. Ensure proper installation height above cooktop. |
| Excessive noise during operation. | Loose components; motor imbalance; ductwork issues. | Check for loose screws or parts. Ensure filters are correctly installed. Inspect ductwork for proper sealing and rigidity. |
| Lights not working. | Light switch off; faulty LED module. | Ensure light knob is in the "ON" position. If lights still fail, contact customer support for LED module replacement. |
Warranty and Support
Elica products are manufactured to high-quality standards and are warranted against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Elica website.
For technical assistance, replacement parts, or to schedule service, please contact Elica customer support. Have your model number and purchase date ready when contacting support.
- Elica Official Website: www.elica.com
- Customer Service: Refer to your product documentation for regional contact information.