Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the Mopar OEM Cruise Control Steering Wheel Switch, part number 68111384AB. This switch is designed specifically for 2011-2019 Dodge Ram 1500 DS models, enabling the vehicle's cruise control functionality. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Product Overview
The Mopar OEM Cruise Control Steering Wheel Switch integrates seamlessly into your vehicle's steering wheel, providing intuitive control over the cruise control system. It features dedicated buttons for activating/deactivating cruise control, setting speed, resuming, canceling, and adjusting gear limits (if applicable to your vehicle's transmission). This genuine Mopar part ensures compatibility and reliable performance.
Figure 1: Front view of the Mopar OEM Cruise Control Steering Wheel Switch, showing the 'GEAR-', 'GEAR+', 'ON/OFF', 'RES+', 'CANCEL', and 'SET-' buttons. A barcode label is visible on the left side.
Figure 2: Angled front view of the cruise control switch, highlighting the ergonomic button layout and the chrome trim around the button panel.
Figure 3: Rear view of the cruise control switch, showing the back casing and a barcode label with the number 28337398. This view also shows the mounting points.
Installation Instructions
Disclaimer: Installation of automotive components can be complex and may require specialized tools and knowledge. If you are not comfortable performing this installation, it is recommended to seek assistance from a certified automotive technician or a Mopar authorized service center. Improper installation can lead to vehicle damage or personal injury.
Tools Required:
- Torx bit set (specific sizes may vary)
- Small flat-head screwdriver or pry tool
- Socket wrench set
- Safety glasses
- Gloves
Procedure:
- Safety First: Before beginning any work, ensure the vehicle's battery is disconnected to prevent accidental airbag deployment or electrical shorts. Wait at least 10-15 minutes after disconnecting the battery for the airbag system's capacitors to discharge.
- Airbag Removal: Carefully follow your vehicle's service manual instructions for safely disengaging and removing the driver's side airbag module from the steering wheel. This typically involves accessing retaining clips or bolts from the rear or sides of the steering wheel.
- Access Old Switch: Once the airbag is safely removed and set aside (face up, away from any objects), locate the existing cruise control switch or the blank cover where the switch will be installed.
- Disconnect Wiring: Gently disconnect the electrical connector(s) from the old switch or the wiring harness if installing in a vehicle without a pre-existing switch.
- Remove Old Switch: Unfasten any screws or clips holding the old switch in place. Carefully remove it from the steering wheel assembly.
- Install New Switch: Position the new Mopar OEM Cruise Control Steering Wheel Switch (Part No. 68111384AB) into the designated slot. Ensure it aligns correctly with the mounting points.
- Connect Wiring: Reconnect the electrical connector(s) to the new switch. Ensure a secure and proper connection.
- Reinstall Airbag: Carefully re-mount the airbag module, ensuring all retaining clips or bolts are securely fastened according to your vehicle's service manual.
- Reconnect Battery: Reconnect the vehicle's battery.
- Test Functionality: Start the vehicle and test the cruise control system to ensure all functions (ON/OFF, SET, RES, CANCEL, GEAR+/-) operate correctly.
Figure 4: Close-up view of the multi-pin electrical connector on the back of the cruise control switch, showing the precise connection points for the vehicle's wiring harness.
Figure 5: Back view of the cruise control switch, displaying the Mopar part number 68111384AB and manufacturing details, including "ASSEMBLED IN MEXICO". This label confirms the authenticity of the OEM part. The barcode 42248205004413 is also visible.
For visual guidance, many online resources and automotive forums provide video tutorials for airbag removal and steering wheel switch replacement specific to 2011-2019 Dodge Ram 1500 models. Search for "Dodge Ram 1500 cruise control switch installation" on video platforms.
Operating Instructions
Once installed and verified, operate the cruise control system using the new steering wheel switch as follows:
- ON/OFF: Press the ON/OFF button to activate or deactivate the cruise control system. An indicator light on your vehicle's dashboard will typically illuminate when the system is active.
- SET-: Once the system is ON, accelerate to your desired speed and press the SET- button to set the current speed. The vehicle will maintain this speed.
- RES+: If cruise control was previously active and then canceled (e.g., by pressing the brake pedal), press the RES+ button to resume the last set speed.
- CANCEL: Press the CANCEL button to disengage cruise control without erasing the set speed from memory. Applying the brake pedal or clutch (manual transmission) will also cancel cruise control.
- Speed Adjustment: While cruise control is active, press SET- to decrease the set speed or RES+ to increase the set speed. Each press typically adjusts the speed by a small increment (e.g., 1 mph or 1 km/h). Holding the button will continuously adjust the speed.
- GEAR- / GEAR+: These buttons are typically used for manual gear selection or limiting the highest gear the transmission can shift into while in cruise control, especially useful for towing or driving on inclines/declines. Refer to your vehicle's owner's manual for specific functionality related to your transmission type.
Always refer to your vehicle's official owner's manual for complete details on cruise control operation and safety guidelines.
Maintenance
The Mopar OEM Cruise Control Steering Wheel Switch is designed for durability and requires minimal maintenance. Keep the switch clean and free from debris. Avoid using harsh chemicals or abrasive cleaners, which could damage the button surfaces or internal components. If the switch becomes dirty, wipe it gently with a soft, damp cloth.
Regularly inspect the steering wheel area for any loose connections or signs of wear. If you notice any unusual behavior or physical damage to the switch, it is recommended to have it inspected by a qualified technician.
Troubleshooting
If you experience issues with your cruise control system after installing the new switch, consider the following troubleshooting steps:
- Cruise Control Not Activating:
- Ensure the ON/OFF button has been pressed and the cruise control indicator light (if present) is illuminated on the dashboard.
- Verify that the vehicle speed is above the minimum activation speed (typically 25-30 mph or 40-50 km/h, refer to your vehicle's manual).
- Check for any active diagnostic trouble codes (DTCs) related to the cruise control system or other vehicle systems that might inhibit its function (e.g., ABS, traction control).
- Inspect the electrical connection to the switch for looseness or corrosion.
- Cruise Control Disengages Unexpectedly:
- Ensure the brake pedal switch is functioning correctly and not sending a false signal.
- Check for any issues with the vehicle's speed sensors.
- Verify that the CANCEL button is not stuck or intermittently activating.
- Buttons Not Responding:
- Confirm the switch is securely mounted and its electrical connector is fully seated.
- Inspect the switch for physical damage or debris lodged under the buttons.
If troubleshooting steps do not resolve the issue, it is recommended to consult a qualified automotive technician or a Mopar authorized service center for diagnosis and repair.
Specifications
| Attribute | Detail |
|---|---|
| Part Number | 68111384AB |
| Compatibility | 2011-2019 Dodge Ram 1500 DS |
| Brand | Mopar |
| Dimensions (Approx.) | 4 x 4 x 2 inches (Package Dimensions) |
| Weight (Approx.) | 0.01 ounces (Package Weight) |
| Manufacturing Location | Assembled in Mexico |
| Date First Available | December 3, 2018 |
Figure 6: Product label from the packaging, confirming the part number 68111384AB and indicating "Made in Mexico" with a packaging date of 2018/10/16. The barcode 0053329927 is also visible.
Warranty and Support
As a genuine Mopar OEM part, this cruise control switch is typically covered by Mopar's standard parts warranty. Warranty terms and conditions may vary, and it is recommended to retain your purchase receipt and consult with the authorized Mopar dealer or the point of purchase for specific warranty details.
For technical support, installation assistance, or warranty claims, please contact an authorized Mopar service center or your local Dodge dealership. They have access to official service information and can provide expert guidance.
You can find more information about Mopar products and support on the official Mopar website or through authorized dealers. Visit Mopar Official Website
