IKRA Thread Spools Replacement Spools (A) Set of 3

Introduction

This manual provides essential information for the proper use and maintenance of your IKRA Thread Spools Replacement Set. These original IKRA accessories are designed to ensure optimal performance for your compatible IKRA grass trimmer. The set includes three thread spools, each with 6 meters of 1.4 mm diameter trimming thread, featuring a semi-automatic tap for thread extension.

Product Overview

Image showing three red IKRA thread spools, each wound with clear trimmer line, ready for installation. These are single thread spools designed for easy replacement.

The IKRA Thread Spools (Model 13001552-3) are genuine replacement parts for various IKRA grass trimmers. Each spool contains 6 meters of durable nylon trimming thread with a thickness of 1.4 mm. The design incorporates a semi-automatic tap mechanism for convenient thread extension during operation.

Compatibility

These thread spools are compatible with the following IKRA grass trimmer models:

• RT 1001 A, RT 1002 A, RT 1003 A, RT 1005 A
• RT 2007 A, RT 2008 A, RT 2122 A, RT 2502 A, RT 2522 A, RT 2502 A Chico, RT 2503 A Chico, RT 2522 A Chico, RT 2524 A Chico
• RT 3002 A, RT 3312 A, RT 3002 A Joker
• RT 5005 A, RT 5006 A
• RT 6005 A, RT 6006 A, RT 6007 A, RT 6008 A, RT 620
• RT 7001 A, RT 8005 A, RT 9002 A
• RT 4001 A Swingline, RTA 12 Swingline, RTA 14.4 Swingline, RTA 18 Swingline
• RTA 2018 LI, RTA 2118 LI, ART 1522 LI

Always verify your trimmer's model number against this list to ensure proper fit and function.

Setup and Installation

1. Safety First: Before attempting to replace the thread spool, ensure your grass trimmer is turned off and disconnected from its power source (unplugged or battery removed).
2. Access the Spool Housing: Locate the trimmer head. Depending on your model, you may need to press release tabs or unscrew a cap to open the spool housing. Refer to your specific trimmer's manual for detailed instructions on opening the head.
3. Remove Old Spool: Carefully remove the old or empty thread spool from the housing. Dispose of it responsibly.
4. Insert New Spool: Take one of the new IKRA thread spools. Ensure the thread is properly wound and secured on the spool. Feed the end of the trimmer line through the eyelet or opening in the trimmer head housing.
5. Secure the Spool: Place the new spool into the housing, aligning any notches or guides. Ensure it sits firmly and correctly.
6. Close Housing: Reattach the cap or cover of the trimmer head, ensuring it clicks into place or is securely screwed on. Pull the trimmer line gently to ensure it extends freely.

If you encounter resistance or difficulty, do not force the spool. Re-check the alignment and consult your trimmer's specific instruction manual.

Operating Instructions

The IKRA thread spools feature a semi-automatic tap system for line extension. To extend the trimmer line during operation:

• Ensure the trimmer is running at full speed.
• Gently tap the trimmer head on a firm, non-abrasive surface (e.g., grass or soft ground).
• The tapping action will release a small amount of line from the spool. The trimmer's line cutter will automatically trim the line to the correct length.

Avoid tapping on hard surfaces like concrete or asphalt, as this can damage the trimmer head or prematurely wear out the line.

Maintenance

Proper maintenance ensures the longevity and performance of your thread spools and trimmer:

• Storage: Store unused thread spools in a cool, dry place away from direct sunlight. Extreme temperatures can affect the integrity of the nylon line.
• Inspection: Before each use, inspect the installed thread spool for any signs of damage or excessive wear. Ensure the line is not tangled or fused.
• Cleaning: Periodically clean the trimmer head and spool housing to remove grass clippings, dirt, and debris that could impede line feeding.
• Line Quality: Use only genuine IKRA replacement spools to ensure compatibility and optimal performance.

Troubleshooting

If you experience issues with your thread spools, consider the following:

• Line Not Feeding:
  • Ensure the trimmer is running at full speed when tapping.
  • Check if the line is tangled or fused inside the spool. Remove the spool and manually unwind a small section if necessary.
  • Inspect the spool housing for debris that might be blocking the line exit.
  • Verify the spool is correctly seated in the trimmer head.
• Line Breaking Frequently:
  • Avoid hitting hard objects (rocks, fences, concrete) with the trimmer line.
  • Ensure the line is not too long, causing excessive strain. The trimmer's line cutter should maintain the correct length.
  • Check for wear or damage on the trimmer head's eyelets where the line exits.
• Spool Not Fitting:
  • Double-check your trimmer's model number against the compatibility list in this manual.
  • Ensure the spool is oriented correctly when inserting it into the housing.

For persistent issues, refer to your grass trimmer's main instruction manual or contact IKRA customer support.

Specifications

Warranty and Support

IKRA is committed to providing high-quality garden tools and accessories. For over 40 years, IKRA has specialized in garden equipment, offering excellent spare parts and customer service.

Spare Parts: Spare parts and accessories for all IKRA garden tools, including grass trimmers, scythes, and brush cutters, can be easily ordered online. IKRA maintains a supply of accessories and spare parts even for older garden tool models.

Customer Service: For any questions, concerns, or support regarding your IKRA products, please refer to the contact information provided with your original grass trimmer purchase or visit the official IKRA website for customer service details.