WAVLINK ARIEAL HS3 - N300 Outdoor WiFi Access Point/Wireless Repeater/Router

1. Introduction

The WAVLINK ARIEAL HS3 - N300 is a versatile outdoor Wi-Fi device designed to extend and enhance your wireless network coverage. It functions as an Access Point, Wireless Repeater, and Router, offering flexible solutions for various networking needs. With its robust weatherproof design and Power over Ethernet (PoE) support, it is ideal for outdoor deployments, providing stable and reliable Wi-Fi connectivity in challenging environments.

2. Safety Information

• Ensure proper grounding to prevent electrical hazards, especially during outdoor installation.
• Do not open or attempt to repair the device. Refer all servicing to qualified personnel.
• Use only the power adapter and accessories provided or recommended by WAVLINK.
• Avoid exposing the device to extreme temperatures outside its operating range (-30°C to 70°C) or continuous moisture beyond its IP65 rating.
• Disconnect power before cleaning or performing any maintenance.

3. Package Contents

Please check the package contents carefully. If any item is missing or damaged, contact your retailer.

• WAVLINK ARIEAL HS3 - N300 Outdoor Wi-Fi Device
• PoE Power Adapter
• RJ-45 Ethernet Cable
• Mounting Kit (Pole Straps/Wall Mount Screws)
• Quick Installation Guide

4. Product Overview

4.1 Device Layout

Figure 4.1: Front View of the Device. This image displays the main unit of the WAVLINK ARIEAL HS3 - N300, highlighting its dual external antennas and the LED indicators for Wi-Fi, WAN/LAN, and Power status. The device is designed for outdoor use with a durable casing.

Figure 4.2: Bottom View of the Device. This image shows the bottom panel of the device, featuring the WAN/LAN port for Ethernet connection, the recessed Reset button (requiring a pin to press for 8 seconds), and the GND (Ground) terminal for proper electrical grounding.

4.2 LED Indicators

• Power LED: Indicates the power status of the device. (On: Powered, Off: No power)
• WAN/LAN LED: Indicates the status of the Ethernet connection. (On: Connected, Blinking: Data activity)
• Wi-Fi LED: Indicates the wireless network status. (On: Wi-Fi active, Blinking: Data activity)

5. Installation

5.1 Physical Installation

The WAVLINK ARIEAL HS3 - N300 is designed for outdoor installation, typically on a pole or wall. Ensure the chosen location provides optimal Wi-Fi coverage and is within reach of a power source (via PoE).

Figure 5.1: Assembly and Cable Connection Diagram. This diagram illustrates the steps for connecting the RJ45 cable to the device and properly sealing the connection for outdoor use. It shows passing the cable through the bottom, middle, and upper spiral covers, connecting to the RJ45 port, and then screwing the covers and rubber seal into place to ensure weatherproofing.

1. Prepare the Cable: Pass the RJ45 Ethernet cable through the bottom spiral cover, then the rubber seal, and finally the upper spiral cover.
2. Connect Ethernet: Connect the RJ45 cable to the WAN/LAN port at the bottom of the device.
3. Secure the Connection: Screw the upper spiral cover onto the device, ensuring the rubber seal is properly seated to provide a waterproof connection. Then, screw the bottom spiral cover into place.
4. Mount the Device: Use the provided mounting kit to securely attach the device to a pole or wall. Ensure it is mounted vertically with antennas pointing upwards for optimal signal.
5. Grounding: Connect a grounding wire to the GND terminal on the device and ensure it is properly grounded to a suitable ground point.

5.2 Power over Ethernet (PoE) Connection

The device is powered via Power over Ethernet (PoE) through the RJ45 cable connected to the PoE adapter.

• Connect one end of the Ethernet cable from the device to the PoE port on the PoE adapter.
• Connect another Ethernet cable from your router/modem or network switch to the LAN port on the PoE adapter.
• Plug the power adapter into a standard electrical outlet.

6. Operation Modes

The WAVLINK ARIEAL HS3 - N300 supports three primary operation modes:

Figure 6.1: Operation Mode Diagrams. This image visually explains the three main modes of operation: WISP Mode (Wireless Internet Service Provider), where the device connects wirelessly to an upstream network and provides wired LAN access; Repeater Mode, where it extends an existing Wi-Fi signal; and Router/AP Mode, where it acts as a primary router or an access point for a wired network.

• Repeater Mode: Extends the coverage of an existing wireless network. Ideal for eliminating Wi-Fi dead zones.
• Router Mode: Creates a new private wireless network, allowing multiple devices to share an internet connection from a modem.
• AP (Access Point) Mode: Converts a wired network connection into a wireless network, providing Wi-Fi access to wired devices.

7. Initial Setup and Configuration

To configure the device, you will typically connect to its default Wi-Fi network or directly via an Ethernet cable and access its web-based management interface.

7.1 Accessing the Web Interface

1. Connect to the Device:
   • Wireless: Search for the default Wi-Fi network (SSID) broadcast by the device (e.g., "WAVLINK_N" or similar) and connect to it. The default password is usually found on a label on the device or in the Quick Installation Guide.
   • Wired: Connect your computer directly to the LAN port of the PoE adapter using an Ethernet cable. Ensure your computer's Ethernet adapter is set to obtain an IP address automatically (DHCP).
2. Open Web Browser: Launch a web browser (e.g., Chrome, Firefox, Edge).
3. Enter IP Address: In the address bar, type the default IP address of the device (e.g., 192.168.10.1 or 192.168.1.1) and press Enter. Refer to the Quick Installation Guide for the exact default IP.
4. Login: Enter the default username and password (e.g., admin for both). You will be prompted to change the password for security reasons.

7.2 Configuration Steps (General)

Once logged in, follow the on-screen wizard or navigate through the settings to configure your desired operation mode.

• Select Operation Mode: Choose between Repeater, Router, or AP mode based on your network requirements.
• Network Settings: Configure WAN settings (for Router mode), LAN IP address, and DHCP server settings.
• Wireless Settings: Set up your Wi-Fi network name (SSID), security type (WPA2-PSK recommended), and password.
• Save and Reboot: After making changes, save your settings and reboot the device if prompted.

8. Maintenance

• Cleaning: Periodically clean the exterior of the device with a soft, dry cloth. Do not use liquid cleaners or aerosols.
• Firmware Updates: Check the WAVLINK official website for the latest firmware updates. Updating firmware can improve performance, add features, and fix bugs. Follow the instructions provided with the firmware update carefully.
• Regular Checks: Periodically inspect cables and connections for any signs of wear or damage, especially in outdoor environments.

9. Troubleshooting

9.1 Common Issues and Solutions

• No Power:
  • Ensure the PoE adapter is properly connected to a power outlet and the device.
  • Check the power LED on the device.
• Cannot Access Web Interface:
  • Verify your computer's IP settings are set to obtain an IP address automatically.
  • Ensure you are using the correct default IP address for the device.
  • Try clearing your browser's cache or using a different browser.
  • If you changed the device's IP address and forgot it, you may need to perform a factory reset.
• No Internet Connection:
  • Check the WAN/LAN LED for activity.
  • In Router mode, ensure your WAN settings (e.g., PPPoE, Dynamic IP, Static IP) are correctly configured.
  • In Repeater mode, ensure the device is successfully connected to the upstream Wi-Fi network.
  • Verify your main router/modem has an active internet connection.
• Weak Wi-Fi Signal or Poor Performance:
  • Relocate the device to a more central position or higher elevation.
  • Ensure antennas are properly oriented.
  • Check for sources of interference (e.g., cordless phones, microwaves).
  • Consider adjusting Wi-Fi channel settings in the web interface.

9.2 Factory Reset

If you forget your login password or encounter persistent issues, you can perform a factory reset to restore the device to its default settings.

• With the device powered on, use a paperclip or a thin object to press and hold the Reset button (located near the WAN/LAN port) for approximately 8 seconds.
• Release the button when the LEDs flash or the device reboots.
• The device will restart with factory default settings. You will need to reconfigure it.

10. Specifications

11. Warranty and Support

11.1 Warranty Information

This product comes with a 1 Year Quality Guarantee and a 180 Days Money Back policy. Please retain your proof of purchase for warranty claims.

11.2 Technical Support

For technical assistance, troubleshooting, or further inquiries, please contact WAVLINK customer support. WAVLINK provides 7x24h Technical Support.

You can also visit the official WAVLINK store on Amazon for more product information and resources: WAVLINK Store