Introduction
This manual provides essential instructions for the safe installation, operation, and maintenance of your Luceco LEXWT7B40P-01 LED Twin Exterior Wall Light with PIR Motion Sensor. Please read this manual thoroughly before installation and retain it for future reference.
Image 1: Overview of the Luceco LEXWT7B40P-01 LED Twin Exterior Wall Light.
Safety Information
- Ensure the power supply is disconnected before installation, maintenance, or cleaning.
- Installation should be performed by a qualified electrician in accordance with local wiring regulations.
- Do not attempt to modify the product. Any modifications may void the warranty and pose safety risks.
- This product is designed for outdoor use and is IP44 rated, providing protection against solid objects larger than 1mm and splashing water from any direction.
- Avoid looking directly into the LED light source when illuminated.
Package Contents
Verify that all components are present before beginning installation:
- 1 x Luceco LED Twin Exterior PIR Wall Light (720LM, 10W, IP44, 4000K, Black)
- Mounting bracket and screws (typically included)
- Instruction Manual
Setup and Installation
The Luceco LEXWT7B40P-01 is designed for straightforward installation. No assembly is required for the light unit itself. Ensure the mounting surface is suitable and can support the weight of the fixture.
- Power Disconnection: Before starting, ensure the main power supply to the installation area is switched off at the circuit breaker.
- Mounting Location: Select a suitable outdoor location for the wall light. Consider the desired coverage area for the light and the PIR sensor.
- Mounting the Bracket: Secure the mounting bracket to the wall using appropriate screws and wall plugs for your surface type.
- Wiring: Connect the AC power supply wires to the terminal block within the light fixture. Ensure correct polarity (Live, Neutral, Earth) according to local electrical codes.
- Attaching the Fixture: Carefully attach the light fixture to the mounted bracket, ensuring a secure fit and proper sealing against moisture.
- Power Reconnection: Once installation is complete and all connections are secure, restore power to the circuit.
Image 2: Side view illustrating the light's profile and potential mounting orientation.
Operating Instructions
The Luceco LEXWT7B40P-01 features adjustable twin LED heads and an integrated Passive Infrared (PIR) motion sensor for automated operation.
Adjusting Light Heads
The two LED light heads are fully adjustable. They can be tilted and rotated to direct the light output precisely where needed. Gently adjust each head to achieve the desired illumination pattern.
PIR Motion Sensor Settings
The PIR sensor detects movement and activates the light. Typically, PIR sensors have adjustable settings for:
- Time: Controls how long the light remains on after motion is detected.
- Lux (Light Sensitivity): Determines the ambient light level at which the sensor becomes active. For example, setting it to a low lux value means the light will only activate in darker conditions.
- Sensitivity (Detection Range): Adjusts the distance and area over which the sensor will detect motion.
Refer to the specific markings or dials on your PIR sensor for precise adjustment methods. These are usually small knobs located on the sensor unit itself.
Image 3: Front view showing the adjustable light heads and the PIR motion sensor.
Maintenance
Regular maintenance ensures optimal performance and longevity of your Luceco exterior wall light.
- Cleaning: Periodically clean the fixture with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or electrical components.
- Inspection: Annually inspect the wiring and housing for any signs of damage, wear, or loose connections. If any damage is found, disconnect power and consult a qualified electrician.
- LEDs: The integrated LED light source is designed for long life and is not user-replaceable.
Troubleshooting
If your Luceco wall light is not functioning as expected, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply; faulty wiring; PIR sensor settings incorrect. | Check circuit breaker. Verify wiring connections. Adjust PIR sensor Lux setting to activate in current light conditions. |
| Light stays on continuously. | PIR sensor detecting constant motion; Time setting too long; faulty sensor. | Ensure no objects are constantly moving in the detection zone. Reduce PIR sensor Time setting. If problem persists, contact support. |
| Light flashes or flickers. | Unstable power supply; loose wiring connection. | Check power supply stability. Inspect and secure all wiring connections (with power off). |
| PIR sensor not detecting motion. | Sensor obstructed; Sensitivity setting too low; incorrect mounting height. | Clear any obstructions from the sensor's view. Increase PIR sensor Sensitivity. Ensure sensor is mounted at an appropriate height for optimal detection. |
If these steps do not resolve the issue, please contact Luceco technical support.
Specifications
| Brand | Luceco |
| Model Number | LEXWT7B40P-01 |
| Product Dimensions | 11L x 7W x 2.6H centimeters (4.33L x 2.76W x 1.02H inches) |
| Item Weight | 0.8 Kilograms |
| Power Source | AC |
| Wattage | 10 W |
| Light Output | 720 Lumens |
| Color Temperature | 4000K (Cool White) |
| IP Rating | IP44 (Protection against splashing water) |
| Material | Aluminum |
| Color | Black |
| Specific Uses | Deck, Driveway, Garden, Pathway, Patio, Walkway |
| Indoor/Outdoor Use | Outdoor |
| Assembly Required | No |
| Batteries Required | No |
Image 4: Dimensional drawing of the light fixture (measurements in millimeters).
Warranty and Support
Luceco provides a dedicated technical support team to assist with any queries or issues you may encounter. For warranty information, please refer to the documentation provided with your purchase or visit the official Luceco website. The warranty typically covers manufacturing defects under normal use conditions.
For technical assistance, please contact Luceco customer service through their official channels.
