YING RAY 2018111110

Download PDF
Contents

YING RAY Replacement Remote Control for Lennox Air Conditioners (Celsius Display) - User Manual

Compatible with Lennox Models: LM012CI, LM012HI, LM018CI, LM018HI, LM024CI, LM024HI, LM036CI, LM036HI Series

1. Introduction

This manual provides detailed instructions for the proper setup, operation, and maintenance of your YING RAY replacement remote control for Lennox Air Conditioners. Please read this manual thoroughly before using the remote control to ensure optimal performance and longevity.

2. Setup

2.1 Battery Installation

The remote control requires two (2) AAA 1.5V ordinary batteries (not included). Follow these steps to install the batteries:

  1. Open the battery compartment cover located on the back of the remote control.
  2. Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
  3. Close the battery compartment cover securely.
YING RAY Replacement Remote Control for Lennox Air Conditioners

Figure 1: YING RAY Replacement Remote Control. The display shows 'FAN AUTO' and '25°C'. Buttons labeled 'ECONO', 'SLEEP', and 'LIGHT' are visible at the bottom. A green label on the remote lists compatible Lennox AC models.

3. Operating Instructions

3.1 General Operation

Point the remote control directly at the indoor unit of your Lennox Air Conditioner. Ensure there are no obstructions between the remote and the unit. The remote control displays temperature in Celsius.

3.2 Button Functions

  • Power Button: Turns the air conditioner ON or OFF.
  • Temperature Adjustment Buttons (Up/Down Arrows): Adjusts the desired temperature setting. The display shows the temperature in Celsius.
  • FAN Button: Cycles through fan speed settings (e.g., Low, Medium, High, Auto).
  • MODE Button: Selects the operating mode (e.g., Cool, Heat, Dry, Fan, Auto). The display may show 'FAN AUTO' when in auto fan mode.
  • ECONO Button: Activates or deactivates economy mode for energy saving.
  • SLEEP Button: Activates or deactivates sleep mode, which adjusts temperature gradually for comfortable sleep.
  • LIGHT Button: Controls the display light on the remote or the indoor unit's panel light.
Remote Control Display showing 25 degrees Celsius

Figure 2: Close-up of the remote control display showing 'FAN AUTO' and a set temperature of '25°C'.

4. Maintenance

4.1 Cleaning

Wipe the remote control with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the surface or internal components.

4.2 Battery Replacement

Replace batteries when the remote control's display becomes dim or its range decreases. Always replace both batteries simultaneously with new AAA batteries. Remove batteries if the remote will not be used for an extended period to prevent leakage.

5. Troubleshooting

If you encounter issues with your remote control, refer to the table below for common problems and solutions:

ProblemPossible CauseSolution
Remote control not respondingDead or incorrectly installed batteries. Obstruction between remote and AC unit. Remote out of range.Replace batteries with new ones, ensuring correct polarity. Remove any obstructions. Move closer to the AC unit.
Display is dim or blankLow battery power.Replace batteries.
AC unit not responding to commandsRemote control not compatible with AC unit. Infrared sensor on AC unit is blocked or faulty.Verify compatibility with your specific Lennox AC model. Ensure AC unit's sensor is clear. Consult AC unit's manual for sensor location.

6. Specifications

FeatureDetail
BrandYING RAY
Model Number2018111110
Compatible AC BrandsLennox
Compatible AC ModelsLM012CI-100V232-1X, LM012CI-100P232-1X, LM018CI-100P232-1X, LM024CI-100P232-1X, LM036CI-100P232-1X, LM012HI-100V232-1X, LM012HI-100P232-1X, LM018HI-100P232-1X, LM024HI-100P232-1X, LM036HI-100P232-1X
Temperature DisplayCelsius
Battery Type2 x AAA 1.5V (not included)
Controller TypeButton Control
Special FeatureErgonomic design

7. Warranty and Support

Specific warranty information for this replacement remote control is not provided in the product details. For any support inquiries or further assistance, please refer to the seller or the point of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.