1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Leuchten Direkt 14019-55 IVEN LED Ceiling Lamp. Please read this manual thoroughly before installation and use to ensure safe and efficient operation. Keep this manual for future reference.
Figure 1: Leuchten Direkt IVEN LED Ceiling Lamp, showcasing its modern, flat design with two illuminated rectangular panels.
2. Safety Instructions
- Electrical Safety: Installation should only be performed by a qualified electrician to prevent electric shock or fire hazards. Always disconnect power at the main circuit breaker before installation or maintenance.
- Indoor Use Only: This product is designed for indoor use in dry environments (IP20 rating). Do not install in bathrooms, outdoors, or areas exposed to moisture.
- Mounting: Ensure the mounting surface can support the weight of the lamp (approximately 970g). Use appropriate screws and anchors for secure installation.
- Cleaning: Disconnect power before cleaning. Use a soft, dry cloth. Do not use abrasive cleaners or solvents.
- LEDs: Do not stare directly into the LED light source when illuminated.
- Disposal: Dispose of the product and its components (including batteries from the remote) according to local regulations.
3. Package Contents
Verify that all components are present and undamaged before proceeding with installation.
- Leuchten Direkt IVEN LED Ceiling Lamp (Model 14019-55)
- Infrared Remote Control (Batteries included)
- Mounting Hardware (screws, anchors)
- Instruction Manual (this document)
4. Setup and Installation
Tools Required: Screwdriver, drill, wire strippers, voltage tester.
- Power Disconnection: Turn off the main power supply at the circuit breaker before starting any electrical work.
- Marking: Hold the lamp base against the ceiling at the desired installation location and mark the drilling points.
- Drilling: Drill holes at the marked points and insert appropriate wall anchors.
- Wiring: Connect the household electrical wires to the lamp's terminal block. Ensure correct polarity (Live, Neutral, Ground). If unsure, consult a qualified electrician.
- Mounting: Secure the lamp base to the ceiling using the provided screws.
- Final Assembly: Ensure all connections are secure and the lamp is firmly attached to the ceiling.
- Power Restoration: Restore power at the circuit breaker.
Figure 2: Product dimensions. The lamp measures 110 cm in length, 25 cm in width, and 7 cm in height.
5. Operating Instructions
The Leuchten Direkt IVEN LED Ceiling Lamp is operated using the included infrared remote control. It features CCT (Correlated Color Temperature) control and continuous dimming.
5.1. Initial Power On
After installation and power restoration, the lamp can be turned on using the remote control or a standard wall switch. The lamp will recall the last selected setting due to its memory function.
Figure 3: The IVEN LED Ceiling Lamp installed on a ceiling, providing bright illumination.
5.2. Memory Function
The lamp retains the last used brightness and color temperature settings when turned off and on again, whether via the remote control or a wall switch.
6. Remote Control Functions
The infrared remote control allows full control over the lamp's features. Ensure the remote has fresh batteries and is pointed towards the lamp for optimal response.
Figure 4: Infrared Remote Control. This image displays the layout and labeling of the remote control buttons.
- ON/OFF (Power Button): Turns the lamp on or off.
- Color Temperature Stage Change (K button): Cycles through preset color temperature stages.
- Night Light (Moon/Stars button): Activates a low-brightness, warm light setting suitable for night use.
- Timer 1 min (Clock button): Activates a 1-minute timer function.
- Dim Up (+ button): Increases the brightness continuously.
- Warm White to Cold White (K+ button): Adjusts the color temperature towards colder white (higher Kelvin).
- Dim Down (- button): Decreases the brightness continuously.
- Cold White to Warm White (K- button): Adjusts the color temperature towards warmer white (lower Kelvin).
7. Maintenance
- Cleaning: Ensure the lamp is switched off and cooled down before cleaning. Use a soft, dry, lint-free cloth to wipe the surfaces. Do not use liquid cleaners, sprays, or abrasive materials.
- LED Replacement: The integrated LED light sources are not user-replaceable. If the LEDs fail, the entire fixture may need professional servicing or replacement.
- Remote Control Batteries: Replace the remote control batteries when its range or responsiveness decreases. Follow the polarity markings inside the battery compartment.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | No power supply; loose wiring; remote control battery depleted. | Check circuit breaker. Verify wiring connections. Replace remote control batteries. |
| Remote control not responding. | Remote control batteries depleted; obstruction between remote and lamp; remote out of range. | Replace batteries. Remove obstructions. Move closer to the lamp. |
| Light flickers or dims unexpectedly. | Unstable power supply; faulty wiring; internal component issue. | Check household electrical system. Consult a qualified electrician. Contact customer support if issue persists. |
| Color temperature or brightness cannot be adjusted. | Remote control issue; lamp malfunction. | Ensure remote control is functioning (see above). If problem persists, contact customer support. |
9. Specifications
- Brand: LeuchtenDirekt
- Model: 14019-55 IVEN
- Dimensions (L x W x H): 110 x 25 x 7 cm
- Weight: 970 g
- Material: Iron, Aluminum, Plastic
- Color: Silver
- Light Source: Integrated LED
- Total Power Consumption: 40 Watts (2 x 20W LED panels)
- Voltage: 230 Volts
- Luminous Flux: 2400 lm
- Color Temperature: 2700K - 5000K (Warm White to Cold White)
- Color Rendering Index (CRI): 80
- Average Lifespan: 25,000 Hours
- Ingress Protection (IP) Rating: IP20 (Indoor use only)
- Special Features: Dimmable, Adjustable Color Temperature, Memory Function, Night Light Function, Timer Function.
- Components Included: LED Ceiling Lamp, Infrared Remote Control.
10. Warranty and Support
Leuchten Direkt products are manufactured with quality and durability in mind. For warranty information, technical support, or service inquiries, please refer to the contact details provided with your purchase documentation or visit the official Leuchten Direkt website. Please retain your proof of purchase for warranty claims.
