FRANKEVER 16-Gauge Hidden Flat Speaker Wire Audio Cable Instruction Manual

1. Setup Guide

This section provides instructions for preparing your FRANKEVER 16-Gauge Hidden Flat Speaker Wire for installation.

1.1 What's Included

• FRANKEVER 16-Gauge Hidden Flat Speaker Wire (50 ft)
• 2 x Quick Connectors

1.2 Recommended Tools

• Scissors or Utility Knife (for cutting wire and removing backing)
• Small Flathead Screwdriver (for securing connectors)
• Heat Gun or Hair Dryer (optional, for removing wrinkles after installation)
• Paint Roller and Paint (optional, for concealing the wire)

1.3 Installation Steps

Follow these steps to properly install your flat speaker wire and connectors.

1. Prepare the Wire End: Cut a piece of flat wire to the desired length. Carefully remove approximately 2cm (0.8 inches) of the white backing from one end of the flat wire to expose the copper conductors.
2. Expose Copper Conductors: Using scissors or a utility knife, carefully cut along the sides of the exposed copper conductors to remove the white edges. This will leave two distinct copper conductors.
3. Fold Copper Conductors: Fold each copper conductor back onto itself two to four times to make it thicker and shorter. This prepares the conductors for insertion into the quick connector.
4. Connect to Quick Connector: Open the quick connector. Insert the folded copper conductors into the designated slots within the connector. Ensure each conductor is fully seated. Snap the connector closed to secure the wire.
5. Attach Speaker Wire to Surface: Peel off the remaining white backing from the adhesive side of the flat wire. Press the wire firmly onto your desired clean, dry surface (e.g., wall, floor, ceiling).
6. Conceal the Wire (Optional): For a completely invisible installation, apply plaster or spackle over the flat wire. Once dry, sand smooth and paint over it to match your wall color.

Figure 1: Diagram illustrating the connection process of the flat speaker wire to the quick connector.

Figure 2: Visual guide for installing the flat speaker wire, including peeling, painting, and final appearance.

2. Operating Instructions

The FRANKEVER 16-Gauge Hidden Flat Speaker Wire is designed for various low-voltage audio and lighting applications.

2.1 Connecting to Devices

Once installed, connect the quick connectors to your desired devices. The wire is suitable for:

• Speakers: Connect to speaker terminals using banana plugs or by directly inserting the exposed wire ends into spring clips/binding posts.
• LED Lighting: Use for low-voltage LED strip connections.
• Other Low Voltage Appliances: Compatible with various low-voltage electrical connections requiring 16-gauge wiring.

Figure 3: Compatible devices for the flat speaker wire.

3. Maintenance

Proper maintenance ensures longevity and optimal performance of your speaker wire.

• Regular Inspection: Periodically check the installed wire for any signs of damage, fraying, or peeling, especially in high-traffic areas or around corners.
• Connection Check: Ensure all quick connectors are securely fastened and that the wire ends are making good contact. Loose connections can lead to signal degradation.
• Cleaning: If the wire is exposed and not painted over, gently wipe it with a dry, soft cloth to remove dust. Avoid harsh chemicals.
• Temperature Stability: Avoid exposing the wire to extreme temperature fluctuations, which can affect the adhesive.

4. Troubleshooting

If you encounter issues with your FRANKEVER 16-Gauge Hidden Flat Speaker Wire, refer to the following common troubleshooting tips:

• No Audio/Signal:
  • Ensure all connections at both the source and destination devices are secure.
  • Verify that the copper conductors are fully inserted into the quick connectors and that the connectors are properly closed.
  • Check for any breaks or damage along the wire's path.
• Poor Sound Quality:
  • Confirm that the wire gauge (16-gauge) is appropriate for the length of your run and the power requirements of your audio system.
  • Inspect for any partial breaks or corrosion on the copper conductors.
• Adhesion Issues:
  • Ensure the surface was clean, dry, and smooth before application.
  • For difficult surfaces, additional adhesive spray or alternative mounting methods may be required.

5. Specifications

6. Warranty and Support

For warranty information or technical support, please refer to the product packaging or contact FRANKEVER customer service directly. Keep your purchase receipt for any warranty claims.