Lorell Conjure Executive Mid-Back Mesh Back Chair LLR62001 Instruction Manual

1. Important Safety Information

Please read all instructions carefully before assembly and use. Retain this manual for future reference.

• Weight Capacity: Do not exceed the maximum weight recommendation of 275 pounds. Exceeding this limit may result in damage to the chair or personal injury.
• Assembly: Ensure the chair is properly assembled and all components, especially the casters, are securely attached before use.
• Stability: Do not stand on the chair. Use the chair only for its intended purpose of seating.
• Moving the Chair: When moving the chair, lift it rather than dragging it to prevent damage to the casters or flooring.

2. Package Contents

Verify that all components are present before beginning assembly. If any parts are missing or damaged, contact Lorell customer support.

• Seat
• Backrest
• Base (with casters)
• Gas Lift Cylinder
• Armrests (2)
• Hardware Pack (screws, washers, Allen wrench)

3. Assembly Instructions

Assembly is required. Follow these steps carefully to ensure proper setup of your Lorell Conjure Executive Mid-Back Mesh Back Chair.

3.1. Attach Casters to Base

Insert each caster into the holes at the end of each leg of the chair base. Push firmly until they click into place.

3.2. Insert Gas Lift into Base

Place the gas lift cylinder into the center hole of the assembled base. Ensure it sits securely.

3.3. Attach Armrests to Seat

Align the armrests with the pre-drilled holes on the underside of the seat cushion. Secure them using the provided screws and Allen wrench. Do not overtighten.

3.4. Attach Backrest to Seat Mechanism

Connect the backrest to the seat mechanism using the designated screws. Ensure the backrest is oriented correctly.

3.5. Connect Seat Assembly to Gas Lift

Carefully place the assembled seat and backrest onto the gas lift cylinder. Apply downward pressure to secure the connection.

Figure 3.5.1: Side view with key dimensions for assembly and fit. Dimensions include 26.8" depth, 26" width, and back height adjustment from 18.9" up to 2.8" higher.

Figure 3.5.2: Top view with key dimensions. Seat width is 20.5", back width is 20.5", and overall width ranges from 24.8" to 25.6".

4. Operating Instructions

Your Lorell Conjure Executive Mid-Back Mesh Back Chair offers multiple adjustments for personalized comfort.

Figure 4.0.1: Overview of chair features including adjustable mesh back, adjustable lumbar support, extra thick padded seat, and independent seat and back angle tilts.

4.1. Seat Height Adjustment

To adjust the seat height, locate the lever on the right side, beneath the seat. While seated, pull the lever up to lower the seat. To raise the seat, stand up and pull the lever up. Release the lever at the desired height.

4.2. Tilt Tension Adjustment

The tilt tension knob is located underneath the front of the seat. Turn the knob clockwise to increase tilt tension (making it harder to recline) or counter-clockwise to decrease tilt tension (making it easier to recline).

4.3. Backrest Angle Adjustment (Ratchet Back)

The ratchet back mechanism allows you to adjust the backrest height. To adjust, lift the backrest upwards in small increments until it reaches the desired height. To lower, lift the backrest to its highest point, then release it to drop to the lowest position, and then re-adjust upwards.

4.4. Lumbar Support Adjustment

The adjustable lumbar support provides ergonomic support for your lower back. Adjust the position of the lumbar support by sliding it up or down on the backrest to find your optimal comfort.

4.5. Seat Slider Adjustment

The seat slider allows you to adjust the seat depth. Locate the lever on the left side, beneath the seat. Pull the lever to unlock the seat, slide the seat forward or backward to your preferred depth, and then release the lever to lock it in place.

Figure 4.5.1: Side view illustrating the various adjustment levers located beneath the seat for height, tilt, and seat slider functions.

5. Maintenance and Care

Proper care will extend the life and appearance of your chair.

• Cleaning: Spot clean the fabric and mesh components as needed. Use a mild detergent and a damp cloth. Do not use harsh chemicals or abrasive cleaners.
• Inspection: Periodically check all screws and connections to ensure they are tight. Retighten if necessary.
• Casters: Keep casters free of debris to ensure smooth movement.

6. Troubleshooting

If you encounter issues with your chair, refer to the following common solutions.

• Chair Sinks or Does Not Stay Up: Ensure the gas lift cylinder is properly seated in both the base and the seat mechanism. If the issue persists, the gas lift may need replacement.
• Chair Wobbles: Check all assembly screws to ensure they are securely tightened. Ensure the base and casters are fully engaged.
• Difficulty Reclining or Adjusting Tilt: Adjust the tilt tension knob (Section 4.2). Ensure no obstructions are preventing movement.
• Casters Not Rolling Smoothly: Check casters for trapped hair or debris and clean as necessary.

7. Specifications

Figure 7.0.1: The Lorell Conjure chair meets ANSI/BIFMA standards for safety and performance.

8. Contact and Support

For further assistance, missing parts, or warranty inquiries, please contact Lorell customer support.

• Manufacturer: Lorell
• Website: Visit the Lorell Store on Amazon
• General Inquiries: Refer to the contact information provided with your purchase documentation or on the official Lorell website.