Introduction
Thank you for purchasing the Esperanza Hachoir EKM032 Meat Grinder. This manual provides essential information for the safe and efficient operation, maintenance, and care of your appliance. Please read these instructions thoroughly before first use and keep them for future reference.
Important Safety Instructions
WARNING: To reduce the risk of fire, electric shock, or injury, always follow basic safety precautions when using electrical appliances.
- Read all instructions before operating the appliance.
- Do not immerse the motor unit in water or other liquids.
- Keep hands and utensils away from moving parts during operation to prevent injury.
- Always unplug the appliance from the power outlet before assembling, disassembling, or cleaning.
- Ensure the appliance is placed on a stable, flat, and dry surface.
- This appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner.
- Use only attachments recommended or sold by the manufacturer.
- Do not use outdoors.
- Do not let the power cord hang over the edge of a table or counter, or touch hot surfaces.
Parts Identification
Familiarize yourself with the components of your meat grinder:
- Motor Unit: The main body containing the motor and control buttons.
- Hopper Plate: Tray for holding meat before grinding.
- Food Pusher: Used to push meat into the grinding mechanism.
- Grinding Head: The housing for the auger, blade, and grinding plates.
- Auger (Feeding Screw): Feeds meat through the grinding head.
- Cutting Blade: Cuts the meat against the grinding plate.
- Grinding Plates: Discs with different hole sizes for fine, medium, or coarse grinding.
- Fixing Ring: Secures the grinding plate and blade to the grinding head.
- ON/OFF/Reverse Switch: Controls the operation of the motor.
Setup and Assembly
Before first use, wash all parts that will come into contact with food in warm soapy water, rinse thoroughly, and dry. Ensure the motor unit is unplugged during assembly.
- Attach Grinding Head: Insert the grinding head into the motor unit opening, aligning the tab on the grinding head with the slot on the motor unit. Rotate clockwise until it locks securely.
- Insert Auger: Place the auger (feeding screw) into the grinding head, ensuring the shaft end fits into the motor drive.
- Position Cutting Blade: Place the cutting blade onto the auger shaft with the sharp edges facing outwards towards the grinding plate.
- Select Grinding Plate: Choose your desired grinding plate (fine, medium, or coarse) and place it over the cutting blade, aligning the notch on the plate with the tab on the grinding head.
- Secure with Fixing Ring: Screw the fixing ring onto the grinding head clockwise until it is hand-tight. Do not overtighten.
- Attach Hopper Plate: Place the hopper plate on top of the grinding head.
- Connect Power: Plug the appliance into a suitable electrical outlet (220V AC).
Operating Instructions
Ensure the appliance is correctly assembled and plugged in before operation.
- Prepare Meat: Cut meat into pieces that fit easily into the hopper opening (approximately 2.5 cm x 2.5 cm x 5 cm). Remove bones, gristle, and excessive fat.
- Place Container: Position a bowl or container under the grinding head outlet to collect the ground meat.
- Start Grinder: Turn the ON/OFF switch to the 'ON' position.
- Feed Meat: Place meat pieces onto the hopper plate and gently feed them into the grinding head using the food pusher. Never use your fingers or other utensils to push meat.
- Reverse Function (if needed): If the grinder becomes jammed, turn the switch to the 'OFF' position, then to 'R' (Reverse) for a few seconds to clear the blockage. Turn off, unplug, and disassemble to clear any remaining blockages if necessary.
- Finish Grinding: Once all meat is ground, turn the switch to 'OFF' and unplug the appliance.
Cleaning and Maintenance
Proper cleaning and maintenance will extend the life of your appliance.
- Unplug: Always unplug the meat grinder from the power outlet before cleaning.
- Disassemble: Disassemble all removable parts in reverse order of assembly.
- Clean Parts: Wash the hopper plate, food pusher, grinding head, auger, cutting blade, grinding plates, and fixing ring in warm soapy water. Use a brush to remove any meat residue.
- Rinse and Dry: Rinse all parts thoroughly with clean water and dry immediately to prevent rust, especially for metal components like the blade and grinding plates.
- Clean Motor Unit: Wipe the motor unit with a damp cloth. Never immerse the motor unit in water or any other liquid.
- Storage: Store the cleaned and dried parts in a safe, dry place. You may apply a thin layer of cooking oil to the metal parts (blade, grinding plates) before storage to prevent rust.
Troubleshooting
If you encounter issues with your meat grinder, refer to the following common problems and solutions:
- Appliance does not start:
- Ensure the power cord is securely plugged into a working outlet.
- Check if the ON/OFF switch is in the 'ON' position.
- Verify that the grinding head is correctly assembled and locked into the motor unit.
- Meat is not grinding or comes out slowly:
- Meat pieces may be too large or contain bones/gristle. Cut meat into smaller, boneless pieces.
- The grinding plate or blade might be clogged. Use the reverse function or disassemble and clean.
- The fixing ring might be too loose. Tighten it slightly.
- Loud noise or unusual vibration:
- Ensure all parts are correctly assembled and tightened.
- Check for foreign objects inside the grinding head.
- If the issue persists, discontinue use and contact customer support.
- Motor stops during operation:
- The appliance may have overheated. Turn off and unplug, allow it to cool down for at least 30 minutes before restarting.
- An overload protection mechanism may have activated. Reduce the amount of meat being processed.
Technical Specifications
| Model Number | EKM032 (S91103062) |
| Brand | Esperanza |
| Power | 2200 Watts |
| Voltage | 220 Volts (AC) |
| Capacity | 5000 Grams |
| Dimensions (L x W x H) | 23 x 23.5 x 27.3 cm |
| Weight | 5 Kilograms |
| Specific Uses | Grinding, Cutting |
Warranty and Customer Support
Esperanza products are manufactured to high-quality standards. For information regarding warranty coverage, please refer to the warranty card included with your purchase or visit the official Esperanza website. For technical assistance, spare parts, or service inquiries, please contact Esperanza customer support through their official channels.
Please retain your proof of purchase for any warranty claims.