1. Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your Nordyne 1016290S Igniter. This component is designed for use in F/M7RL and M7TL furnace models. Please read this manual thoroughly before attempting any procedures.
Figure 1: The Nordyne 1016290S Igniter, shown in its packaging. This image displays the igniter unit with its white ceramic body, black heating element, and electrical connector, alongside its product label.
2. Safety Information
- Electrical Hazard: Always disconnect power to the furnace at the main circuit breaker before inspecting, installing, or servicing any electrical components. Failure to do so can result in serious injury or death.
- Hot Surfaces: Furnace components can be extremely hot. Allow sufficient time for the furnace to cool down before handling any parts.
- Qualified Personnel: Installation and servicing should ideally be performed by a qualified HVAC technician.
- Personal Protective Equipment: Wear appropriate personal protective equipment (PPE) such as gloves and safety glasses during installation and maintenance.
3. Package Contents
- 1 x Nordyne 1016290S Igniter F/M7RL,M7TL Furnace (2017 NEW STYLE)
4. Compatibility
The Nordyne 1016290S Igniter is compatible with the following furnace models:
- Nordyne F/M7RL Furnaces
- Nordyne M7TL Furnaces
This igniter is a replacement for part number 1016290S and is designed for the 2017 new style furnaces. Always refer to your furnace manufacturer's recommendations for proper fit and compatibility.
5. Setup and Installation
Follow these steps to safely replace your furnace igniter. It is recommended to consult a qualified technician if you are unsure about any step.
- Disconnect Power: Locate the main power switch for your furnace and turn it off. For added safety, turn off the corresponding circuit breaker at your electrical panel.
- Access Furnace: Open the furnace access panel or lid to expose the internal components.
- Locate Old Igniter: Identify the existing igniter. It is typically located near the burners.
- Remove Old Igniter: Carefully disconnect the electrical wires from the old igniter. Unscrew or unclip the igniter from its mounting bracket. Handle the old igniter with care as it may be fragile.
- Install New Igniter: Secure the new Nordyne 1016290S Igniter into the mounting bracket. Ensure it is firmly in place.
- Connect Wiring: Connect the electrical wires to the new igniter. Ensure connections are secure and correct according to the furnace wiring diagram.
- Close Furnace: Close and secure the furnace access panel.
- Restore Power: Restore power to the furnace at the circuit breaker and then at the furnace's main power switch.
- Test Operation: Initiate a heating cycle to verify the new igniter functions correctly and the furnace ignites properly.
Video 1: This video demonstrates the general process of replacing a furnace flame sensor, which is similar to replacing an igniter. It covers steps such as turning off power, accessing the furnace, removing the old component, and installing the new one. While the video shows a flame sensor, the physical steps for replacing an igniter are analogous.
6. Operating Instructions
The Nordyne 1016290S Igniter operates automatically as part of your furnace's ignition sequence. When the thermostat calls for heat, the igniter will:
- Receive an electrical signal to heat up to a high temperature.
- Glow red-hot, providing the necessary heat to ignite the gas flowing from the burners.
- Once ignition is confirmed by the flame sensor, the igniter will typically turn off, and the furnace will continue its heating cycle.
No manual operation is required for the igniter itself.
7. Maintenance
To ensure optimal performance and longevity of your Nordyne 1016290S Igniter, consider the following maintenance tips:
- Annual Inspection: Have your furnace, including the igniter, inspected annually by a qualified HVAC technician.
- Cleanliness: Keep the area around the igniter free from dust, debris, and obstructions. A clean igniter operates more efficiently.
- Avoid Touching: Do not touch the ceramic or heating element of the igniter with bare hands, as oils from your skin can create hot spots and shorten its lifespan.
8. Troubleshooting
If your furnace is not igniting or experiencing issues, the igniter may be a contributing factor. Here are some common troubleshooting steps:
| Symptom | Possible Cause | Solution |
|---|---|---|
| Furnace not igniting, igniter does not glow. | No power to furnace, faulty igniter, wiring issue. | Check furnace power switch and circuit breaker. Inspect igniter wiring for loose connections. If power is present and wiring is secure, the igniter may need replacement. |
| Igniter glows but gas does not ignite. | No gas supply, faulty gas valve, igniter not hot enough. | Verify gas supply to the furnace is open. Ensure the igniter is glowing brightly. If issues persist, a gas valve or igniter replacement may be necessary. Consult a technician. |
| Furnace cycles on and off rapidly (short cycling). | Dirty flame sensor (often confused with igniter issues), airflow problems. | Inspect and clean the flame sensor (a separate component, usually next to the igniter). Check air filters for blockage. |
For complex issues or if you are uncomfortable performing these steps, contact a certified HVAC professional.
9. Specifications
- Part Number: 1016290S
- Brand: Nordyne
- Model: 1016290S
- Item Weight: 1.76 ounces
- Package Dimensions: 9.33 x 2.13 x 1.69 inches
- Manufacturer Part Number: 1016290S
- First Available Date: December 21, 2017
- Construction: Precision construction, designed for durability and heat resistance.
Video 2: This video provides a detailed look at the features and construction of a furnace igniter, highlighting its materials and design for high temperature resistance and durability. It also mentions compatibility with various Nordyne furnace models.
10. Warranty and Support
This Nordyne igniter is covered by the manufacturer's standard warranty. For specific warranty details, claims, or technical support, please refer to the documentation provided with your furnace or contact Nordyne customer service directly. Keep your purchase receipt as proof of purchase.
