Yardlock Keyless Gate Lock (Model MBX) Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Yardlock Keyless Gate Lock, Model MBX. This system offers secure, keyless 2-way access for wood or vinyl gates, designed for theft prevention and home security.

What's in the Box

The Yardlock Keyless Gate Lock package includes the following components:

• Gate Lock Unit (with combination dials)
• Latch Cover
• Latch Parts (including latch arm and mechanism)
• Hardware (screws, cable)

Image: Components included in the Yardlock Keyless Gate Lock package.

Gate Compatibility

The Yardlock Gate Lock is designed for installation on wood or vinyl gates. It is compatible with gates that swing either into or out of the yard. For optimal security and functionality, ensure your gate post is at least 3.5 inches thick. If the gate post is less than 3.5 inches, a 2x4 wood piece is required on the outside of the post for proper installation.

Image: Visual guide for gate compatibility, highlighting suitability for wood and vinyl gates.

Setup and Installation

Installation requires a tape measure, electric drill, Phillips bit, and a wood drill bit. All necessary hardware is included. Follow these steps carefully for proper installation:

1. Mark Latch Position

On the inside of your gate, mark the desired height for the latch. This should be no higher than 44 inches (112 cm) from the ground and at least 18 inches (46 cm) below the top of the gate.

2. Install Latch Arm

Hold the latch arm on the edge of the gate at the marked height and mark the screw holes. Secure the latch arm using the provided screws.

3. Install Latch Mechanism

Align the latch mechanism on the gate post with the latch arm and mark the screw holes. Mount the latch mechanism to the post using the provided screws.

4. Drill Cable Hole

Push the top of the latch mechanism against the post and mark the post. Drill a horizontal 3/8-inch hole through the post at a slight angle, ensuring the hole exits near the center on the other side.

5. Install Latch Cover

Feed the cable through the drilled hole. Using the longest screw provided, secure the latch cover at the top. Then, use the two shorter screws to secure the bottom of the latch cover.

6. Install Gate Lock Unit

On the outside of the post, slide the cable through the back hole of the Yardlock unit and align it with the hole on the post. Mark the locations for the four screw holes. Secure the Yardlock unit with the provided screws, being careful not to overtighten.

7. Connect Cable to Lock Unit

With the Yardlock unit fully open, slide the cable through pins A and B. Pull the cable tight and install screw A. Slightly lift the cable and loop it around pin B and under itself between pins A and B. Install screw into pin B and tighten. Tuck the remaining cable into the back of the Yardlock unit and close the unit.

8. Set Personal Code

The factory setting is "0000". To set your personal code, open the Yardlock unit and remove the rubber block. Push the lever left and forward in the direction of the arrow. Rotate the dials to your desired 4-digit combination. For better security, avoid duplicate or sequential digits. Push the lever back up and to the right to its original position. Reinstall the rubber block and close the Yardlock unit.

Image: Visual overview of the installation steps for the Yardlock Gate Lock.

Installation Video

Video: Detailed guide on how to install your Yardlock Gate Lock.

Operating Instructions

To Enter Your Yard (from outside):

1. Open the weather guard cover.
2. Enter your personal 4-digit code.
3. Open the Yardlock unit. This will pull the internal wire, lifting the latch on the other side of the gate.
4. Open the gate and enter.
5. Before walking away, close the Yardlock unit, scramble the numbers to lock it, and close the weather guard cover. The gate will automatically lock behind you.

To Exit Your Yard (from inside):

1. Simply lift the latch mechanism on the inside of the gate. No code is needed.
2. Open the gate and exit.
3. Close the gate behind you. The gate will automatically lock.

Operation Video

Video: Demonstration on how to use your Yardlock Gate Lock for entry and exit.

Changing Your Combination

To change your personal code, repeat the steps outlined in the "Set Personal Code" section (Step 8 of Setup and Installation), starting with your current code. Codes can be changed as often as necessary.

Maintenance

The Yardlock Gate Lock is constructed from durable, waterproof, and rust-resistant materials, requiring minimal maintenance. Periodically inspect the unit for any debris or obstructions that might affect the smooth operation of the dials or the latch mechanism. Clean with a damp cloth as needed. Avoid using harsh chemicals that could damage the finish.

Image: Features emphasizing the durability and weather resistance of the lock.

Troubleshooting

• Difficulty opening/closing: Ensure the gate is properly aligned and not sagging. Check for any obstructions around the latch mechanism or the cable path.
• Combination dials stiff: Clean the dials and apply a small amount of dry lubricant if necessary.
• Cable not pulling latch: Verify the cable is correctly installed and tightened within the lock unit and is not frayed or obstructed.

Specifications

Support

For further assistance, technical support, or inquiries regarding your Yardlock Keyless Gate Lock, please refer to the contact information provided in your product packaging or visit the official Yardlock website.