1. Introduction
The Insta360 Dive Case is specifically designed for the Insta360 ONE X Panoramic Action Camera, enabling its use in underwater environments. This robust housing provides waterproof protection up to a depth of 30 meters (98 feet), allowing for seamless 360-degree underwater video and photo capture. It features a 1/4-inch screw mount for compatibility with various accessories.
This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your Insta360 Dive Case.
2. Safety Information
- Always perform a leak test with the case empty before first use and after any significant impact or maintenance. Submerge the empty case in shallow water for at least 30 minutes.
- Ensure the O-ring seal is clean and free from dust, sand, hair, or any debris before closing the case. A small amount of silicone grease can be applied to the O-ring to maintain its elasticity and sealing properties.
- Do not exceed the maximum waterproof depth of 30 meters (98 feet). Exceeding this limit may cause damage to the case and your camera.
- Avoid sudden temperature changes, which can cause condensation inside the case. Use anti-fog inserts to prevent fogging.
- After each use in saltwater, rinse the dive case thoroughly with fresh water and allow it to air dry. Do not use detergents or abrasive cleaners.
- Handle the case with care to prevent scratches on the lens domes, which can affect image quality.
3. Package Contents
Verify that all items are present in your package:
- Insta360 Dive Case for ONE X
- Anti-fog inserts
- Microfiber cleaning cloth
- 1/4-inch screw mount adapter
4. Setup and Installation
4.1 Installing the Insta360 ONE X Camera
- Open the dive case by unlatching the locking mechanism.
- Carefully insert your Insta360 ONE X camera into the case, ensuring it is properly aligned with the internal guides and the lens domes.
- Place one or two anti-fog inserts into the designated slots inside the case to prevent condensation.
- Inspect the O-ring for any debris or damage. Close the case firmly, ensuring the locking mechanism clicks securely into place.
Figure 1: Insta360 Dive Case with ONE X camera installed.
4.2 Attaching to Mounts
The dive case features a standard 1/4-inch screw mount at the bottom, allowing it to be attached to various camera accessories such as selfie sticks, tripods, or specialized underwater mounts.
- Align the 1/4-inch screw mount adapter (if using) or your accessory's screw with the dive case's mount.
- Rotate clockwise to tighten securely. Do not overtighten.
5. Operating the Dive Case
5.1 Underwater Operation
- Before diving, ensure the camera is powered on and in the desired recording mode. It can be challenging to see the camera's screen through the case underwater, especially in bright sunlight.
- The dive case provides access to the camera's buttons via external push-buttons. Press these buttons firmly to operate the camera's functions (e.g., start/stop recording, change modes).
Figure 2: External buttons on the Dive Case for camera control.
5.2 Seamless Underwater Stitching
The Insta360 Dive Case is designed to minimize visual distortion and enable seamless stitching of 360-degree footage underwater. For optimal results, ensure your camera's firmware is up to date and use the Insta360 Studio software for post-processing, selecting the 'Dive Case' option for underwater footage.
Note: While designed for seamless stitching, some minor visual artifacts may occur depending on lighting conditions and proximity to objects.
6. Maintenance
- Cleaning: After each use, especially in saltwater, rinse the entire dive case with fresh water. Gently wipe the lens domes with the provided microfiber cloth. Do not use harsh chemicals or abrasive materials.
- O-Ring Care: Periodically inspect the O-ring for cracks, tears, or deformation. Clean it with fresh water and apply a thin layer of silicone grease to keep it pliable. Replace the O-ring if any damage is observed.
- Storage: Store the dive case in a cool, dry place away from direct sunlight. Keep the case slightly open or with the O-ring removed to prevent compression set if storing for extended periods.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leakage | Damaged or dirty O-ring; improper closure; exceeding depth limit. | Inspect and clean O-ring, apply silicone grease, ensure proper closure, do not exceed 30m depth. Replace O-ring if damaged. |
| Internal fogging | Humidity inside case; temperature difference. | Use fresh anti-fog inserts. Assemble case in a dry environment. |
| Buttons unresponsive | Camera not properly seated; debris obstructing button mechanism. | Re-seat camera, check for obstructions, ensure firm button presses. |
| Poor stitching in footage | Outdated firmware; incorrect post-processing settings. | Update camera firmware. Use Insta360 Studio and select 'Dive Case' stitching option. |
8. Specifications
- Brand: Insta360
- Model Name: CINOXWH/A
- Compatible Devices: Insta360 ONE X
- Water Resistance Level: Waterproof
- Maximum Waterproof Depth: 30 meters (98 feet)
- Material: Polycarbonate (PC), Stainless Steel
- Mounting Type: 1/4-inch Base Mount
- Item Weight: 0.23 Kilograms
9. Warranty and Support
For warranty information and technical support, please refer to the official Insta360 website or contact their customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.
Official Insta360 Website: www.insta360.com
